Abstract:The thermal conversion of waste plastic products can provide a promising solution to the issues of environmental pollution, waste management, and energy needs. However, our present understanding on the thermal reforming of different kinds of plastic wastes mixtures during their co-pyrolysis and co-gasification for syngas production and energy recovery is insufficient. Non-selective urban polypropylene (PP) and polystyrene (PS) waste plastics were chosen for the investigations reported here. Thermal degradation properties of PP and PS as well as their blends in different mass ratios were investigated via thermogravimetric (TG) analysis. Co-pyrolysis and CO 2 -assisted co-gasification of PP-PS blends were then conducted using a fixed-bed reactor at a temperature of 1173 K. Experimental results from the blends were then compared with the weighted value calculated from their component feedstocks to quantify the degree of synergistic effect. TG results showed that the co-treatment of PP and PS enhanced the respective devolatilization process. The co-pyrolysis of PP and PS enhanced their thermal cracking, leading to synergistic increases in the yields of H 2 , light hydrocarbons (HC) and total syngas. In co-gasification, the reforming reaction involving CO 2 was synergistically enhanced, resulting in the increased yields of H 2 and HC. The gasification reactivity of carbon black improved during the co-processing of PP and PS due to the synergistic effect between the two different kinds of plastics. Higher synergistic effects were observed from the plastic mixtures having higher PS content that resulted in increased yield of syngas. Co-gasification of PP-PS blends having 40% PP content (2P3S) exhibited the maximum synergistic effect on H 2 , CO, and total syngas showing increased yields by 88.8%, 77.7%, and 74.2% respectively. The lowest synergistic effect was observed for HC that showed increased yield of only 25.1%. The optimal CO 2 consumption was also observed from the co-gasification of 2P3S. Each gram of 2P3S feedstock consumed approximately 1.80 g of CO 2 to result in highest recovered energy of 27.49 kJ/g and the maximum overall energy efficiency of 43.2%. The results revealed that enhanced thermal cracking and CO 2 reforming reaction, along with the improved reactivity of carbon black were mainly responsible for increased yields of H 2 , HC, CO and total syngas during co-gasification. This study contributes to the fundamental understanding of co-processing of non-separated waste plastics for enhanced syngas production and energy recovery, elucidating the synergistic effect between the various kinds of plastics during their co-pyrolysis and co-gasification.

Comparative assessment on thermo-chemical conversion of different waste plastics to value added syngas: thermodynamic investigation

An Investigation of a Hybrid Plasma Gasification System for Various Waste Plastics Thermochemical Degradation in the Fuel Extraction Process

Syngas and hydrogen production from co-gasification of rice husk biomass and plastic waste mixture using Aspen Plus

Two-stage thermal pyrolysis of plastic solid waste: Set-up and operative conditions investigation for gaseous fuel production

Plastic-containing food waste conversion to biomethane, syngas, and biochar via anaerobic digestion and gasification: Focusing on reactor performance, microbial community analysis, and energy balance assessment

Integration of Methane Reforming and Chemical Looping Technologies for Power Generation from Waste Plastic: Technical and Economic Assessment

Techno-economic analysis and life cycle assessment of mixed plastic waste gasification for production of methanol and hydrogen

Life Cycle Assessment of Pyrolysis, Gasification and Incineration Waste-to-energy Technologies: Theoretical Analysis and Case Study of Commercial Plants.

Thermochemical Valorization of Waste Plastic for Production of Synthetic Fuels, Fine Chemicals, and Carbon Nanotubes

Co-processing plastics waste and biomass by pyrolysis–gasification: a review

Synergistic effects during co-pyrolysis and co-gasification of polypropylene and polystyrene

Development and evaluation of an integrated waste to energy system based on polyethylene plastic wastes pyrolysis for production of hydrogen fuel and other useful commodities

Opportunities for converting waste plastics into petrochemicals: Process design, multi-objective optimization, and omnidirectional techno-economic-society-environment assessment

Co-gasification of plastic waste blended with coal and biomass: a comprehensive review

An Aspen plus process simulation model for exploring the feasibility and profitability of pyrolysis process for plastic waste management

Applications of H 2 -Enriched syngas and slag products from plastic wastes via novel plasma dual-stage-arc pyrolysis

Recent Development of Biomass and Plastic Co-Pyrolysis for Syngas Production

Thermochemical Conversion of Biomass for Syngas Production: Current Status and Future Trends

Thermodynamic analyses of synthetic natural gas production via municipal solid waste gasification, high-temperature water electrolysis and methanation

Pilot Scale Pyrolysis and Simulation of Plastic Waste into a Value‐Added Product: An Integrated Approach

Experimental study on CO 2 co-gasification characteristics of biomass and waste plastics: Insight into interaction and targeted regulation method