Abstract:Blending with polyethylene (PE) is a conventional way to improve the low‐temperature toughness of polypropylene (PP). However, the mechanical deformation behavior of PP/PE blends at different temperature has not been fully revealed, and the enhancement of low‐temperature toughness was far less than expected. To enhance the low‐temperature toughness of PE/low density polyethylene (LDPE) blends system, which was a crucial blend for polyolefin materials with wide application in frigid regions, the PP/LDPE blend foam samples with stretched cells were fabricated via a facile injection foaming together with open‐mold stretching process. During the open‐mold stretching, the relatively miscible PP and LDPE chains were debonded, and then the stretched and oriented cells structure with lots of tiny inter‐phase cavities between the PP and LDPE phases and the fine lamellae were formed in the blend foam system. Such inter‐phase cavities provided an adequate movement space for the frozen PP and LDPE chains and lamellae, and effectively relaxed and transferred stress, when compressed at ‐25 °C, which greatly promoted the uniform compressive behavior accompanied by the completely compacted cells. Moreover, the compressive fracture surface changed from relatively flat and smooth for the stretched PP foam to obvious yield folds and deformation for the stretched blend foam, and the compressive strain of stretched PP/LDPE blend foam was highly enhanced by a roughly 31%, 53% and 44% increase than that of PP, PP/LDPE and stretched PP foam samples, respectively, achieving the low‐temperature brittle‐ductile transition for PP. This work provides a facile strategy for fabricating PP/LDPE blend with good low‐temperature toughness and promising application potentials. This article is protected by copyright. All rights reserved.

Brittle Ductile Transition of POE Toughened HDPE and Its Lowest Rigidity Loss: Effect of HDPE Molecular Weight

Brittle-ductile transition of elastomer toughened HDPE: effect of elastomer modulus

Research on Toughening Modification of Copolymerized Polypropylene Using Polyolefin Elastomers

Brittle–ductile transition of PP/POE blends in both impact and high speed tensile tests

Effect of polypropylene molecular weight distribution on the balance between the toughness and rigidity of the impact polypropylene composites

Ductile–brittle transition controlled by isothermal crystallization of isotactic polypropylene and its blend with poly(ethylene-co-octene)

Effect of Morphology Development on the Low‐temperature Tensile Properties of PP / POE Blends

THE MECHANICAL AND MELTING CRYSTALLIZATION PROPERTIES OF β-FORM POLYPROPYLENE/POE BLENDS

Study on properties of HDPE/LLDPE/POE blown films

New Insight on Improving Electrical Strength and Toughness of Polyethylene Blends: Turning Point of Supramolecular Structure

Mechanism of low‐temperature brittle‐ductile transition of polypropylene/low‐density polyethylene blend foam under compressive stress caused by cells stretching

Morphology and Dynamic Mechanical Properties of High Density Polyethylene/petroleum Resin/polyethylene–octylene Elastomer Blends

Realizing Simultaneous High‐temperature Strength and Low‐temperature Elongation in Polyolefin Elastomer Toughened Polypropylene Via Controlling the Dispersed Phase Size

Brittle-tough transition in PP/EPDM blends: effects of interparticle distance and temperature

Unique crystal morphology and tensile properties of injection-molded bar of LLDPE by adding HDPE with different molecular weights

Correlation Between Oxidation-induced Crosslinking and Rheological Behavior of HDPE

Thermal, mechanical, and dielectric behaviors of crosslinked linear low density polyethylene/polyolefin elastomers blends

Mechanical Properties and Microstructure of the HDPE/Al(OH)3/POE Composite

Effects of viscosity ratio on properties and structure of PP/POE blends

The Chain Dis-Entanglement Effect of Polyhedral Oligomeric Silsesquioxanes (POSS) on Ultra-High Molecular Weight Polyethylene (UHMWPE)

Physical and Thermal Properties of High-Density Polyethylene Film Modified with Polypropylene and Linear Low-Density Polyethylene