Abstract:The coarse segregative eutectic phases, emerged in the twin roll casting (TRC) process of Mg strips, which cannot be resolved solely by controlling the processing variables or post heat treatment, are detrimental to the subsequent rolling deformation. Considering it, we introduce the pre-rolling steps on the TRC Mg-4Al-2Sn-1 Zn (ATZ421) alloys, which is expected to facilitate the dissolution of these segregative phases by increasing distortion of crystal lattices and rolling stress, and further investigate the effect of a single pass or two passes pre-rolling on the microstructure evolution and tensile properties. It indicates that the pre-rolled alloy with two passes presents more uniform precipitates and higher twinning density in comparison with that using a single pass. The uniform distribution of precipitates in two passes pre-rolling is due to the increase in density of dislocations and deformed twins, which results in more distortion of crystal lattices with more stored energy, facilitating the diffusion of solutes. Moreover, the pre-rolling of two passes introduces more rolling stress into Mg matrix, which is beneficial for the crush of coarse eutectic phases, and further accelerates the sufficient dissolution of second phases. After the subsequent rolling and annealing processes, the sheet with pre-rolling deformation of two passes shows finer microstructure, which mainly benefits from the pinning effects of uniform nano-sized precipitates. As a result, the annealed sheet with two-pass pre-rolling deformation exhibits an advantageous combination of high strength and high ductility with fine microstructure, showing an ultimate tensile strength of similar to 297 MPa, a yield strength of similar to 205 MPa and an elongation of 25.0%. This work provides an effective method of dissolving the coarse segregative phases in the TRC Mg alloys with significant potential for industrial production.

Enhanced Precipitation Strengthening of Mg-Al-Sn-Ca Alloy by Multidirectional Rolling

Elucidating Dynamic Precipitation and Yield Strength of Rolled Mg–Al–Ca–Mn Alloy

Spheroiding and Refining of Coarse CaMgSn Phase in Mg–Al–Sn–Ca Alloys for Simultaneously Improved Strength and Ductility Via Sub-Rapid Solidification and Controlled Rolling

Dramatic Improvement of Formability in Mg-3Al-1Sn-0.5Ca-0.1Sm Alloy Via Mn Microalloying Combined with High Temperature Rolling

Prominent Role of High-Volume Fraction Mg17Al12 Dynamic Precipitations on Multimodal Microstructure Formation and Strength-Ductility Synergy of Mg–Al–Zn Alloys Processed by Hard-Plate Rolling (HPR)

Microstructure and Tensile Properties of Rolled Mg-4Al-2Sn-1Zn Alloy with Pre-Rolling Deformation

Dynamic precipitation and twinning-induced dynamic recrystallization in Mg–6Al–3Sn–1Zn alloy during multi-pass high-speed rolling

Non-basal Slips Mediated Dynamic Recrystallization Promote Synergistic Strengthening and Toughening of Centrifugal Casting Mg–1.1Mn–0.5Al Alloy via High Strain Rolling

Effects of Rolling Deformation on Precipitation Behavior and Mechanical Properties of Al–Zn–Mg–Cu Alloy

Effect of twin assisted precipitation on the microstructure and mechanical properties of gradient structure Mg-Gd-Zn-Zr alloy

Microstructure Evolution and Mechanical Properties of Mg-3al-3sn-1zn Alloy During Multi-Pass High-Speed Rolling

Enhancing Mechanical Properties of Rolled Mg-Al-Ca-Mn Alloy Sheet by Zn Addition

Pre-precipitating promoted by microshear bands effectively circumvents strength-ductility trade-off of RT-rolled Al–6Zn–1Mg alloy

A Rolled Mg‐8Al‐1Sm‐1Zn Alloy with High Strength‐Ductility via Single‐Pass Liner Rolling

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

Deformation Induced Dynamic Recrystallization and Precipitation Strengthening in an Mg-Zn-Mn Alloy Processed by High Strain Rate Rolling

Achieving High Strength-Ductility Synergy Through High-Density Coherent Precipitation in Twin-Roll Cast Al–Zn–Mg–Cu Strips

Balancing the Strength and Ductility of Mg-6Zn-0.2Ca Alloy Via Sub-Rapid Solidification Combined with Hard-Plate Rolling

A high-performance Mg-Al-Sn-Zn-Bi alloy fabricated by combining sub-rapid solidification and hot rolling

Developing High-Strength and Ductile Mg-Gd-Y-Zn-Zr Alloy Sheet Via Bimodal Grain Structure Coupling with Heterogeneously-Distributed Precipitates

Effect of Warm Rolling on the Microstructure, Texture and Mechanical Properties of Extruded Mg–Zn–Ca–Ce/La Alloy