Abstract:First, different PP foam samples were prepared by different core‐back distances of the mold in the injection molding machine above the picture, and they can be summarized into two categories: high cell density PP foam material (with a fine and dense cell structure) and low cell density PP foam material (with a large size distribution of uneven cell structure). Below the injection molding machine are the flame retardant mechanisms of the two foam materials, which can generate two different carbon layer structures through continuous burning. At the far right of the picture is the reason for the two different carbon layers, mainly due to the different degrees of gas escape from the PP foam materials during combustion. In previous studies, the effect of cell structures of polypropylene (PP) foam materials on flammability behavior had been largely overlooked. In this work, ammonium polyphosphate and pentaerythritol were used as intumescent flame retardants (IFR) for PP, and then the PP‐IFR flame retardant foams were prepared by using injection foaming technology with two different weight reduction methods (same mold volume before foaming and after foaming). The results showed that the average cell size of all the PP‐IFR flame retardant foams in the 10% to 30% weight reduction was less than 100 μm. The PP‐IFR flame retardant foams with an average cell diameter of 26.22 μm and cell density of 7.88 × 106 cells/cm3 had the best limiting oxygen index (LOI) of 27.9%. In addition, the PP‐IFR flame retardant foams with better foaming quality had a higher LOI and a denser foam carbon layer whatever the weight reduction methods, resulting in better flame retardant properties. The escape of gases from the foamed and un‐foamed areas not only reduced the concentration of flammable gases but also led to the collapse and rupture of the foam carbon layer during the combustion process. Hence, it provides guidance for preparing PP foam materials with excellent flame retardancy.

Lightweight and Strong Pp/Talc/Ptfe Foams with Enhanced Flame-Resistant Performance Fabricated by Microcellular Foam Injection Foaming

Lightweight and strong polypropylene/talc/polytetrafluoroethylene foams with enhanced flame-retardant performance fabricated by microcellular foam injection foaming

Injection Molded Strong Polypropylene Composite Foam Reinforced with Rubber and Talc

Microcellular injection molded outstanding oleophilic and sound-insulating PP/PTFE nanocomposite foam

Lightweight and High Impact Toughness PP/PET/POE Composite Foams Fabricated by In Situ Nanofibrillation and Microcellular Injection Molding

In Situ Nanofibrillar Polypropylene-Based Composite Microcellular Foams with Enhanced Mechanical and Flame-Retardant Performances

Mold-opening foam injection molded strong PP/CF foams with high EMI shielding performance

Development of High Thermal Insulation and Compressive Strength BPP Foams Using Mold-Opening Foam Injection Molding with In-Situ Fibrillated PTFE Fibers

High Thermal Insulation and Compressive Strength Polypropylene Foams Fabricated by High-Pressure Foam Injection Molding and Mold Opening of Nano-Fibrillar Composites

High-strength, impact-resistant PP/PTFE composite foam with enhanced surface appearance achieved through mold-opening microcellular injection molding

Tailored Morphologies and Properties of High-Performance Microcellular Poly(phenylene Sulfide)/poly(ether Ether Ketone) (PPS/PEEK) Blends

Fabrication of Lightweight Polyphenylene Oxide/High‐Impact Polystyrene Composite Bead Foam Parts via In‐Mold Foaming and Molding Technology

Tough and Defect-Free-surfaces PA66/PTFE Composite Foam with Bimodal Structure Achieved by High-Pressure Foam Injection Molding with Mold-Opening

Effect of foaming behavior of polypropylene foams on flame retardant properties under different weight reduction methods

Lightweight and High-Performance Polymethacrylimide Foams for Complex-Shaped Applications Based on the Highly Foamable Precursor Beads

Fabrication of Polyether–Ether–Ketone Foams with Superior Properties and Mitigated Weld Lines by Microcellular Injection Molding

Real-microcellular poly(ether-block-amide)/carbon fiber foams with improved mechanical property and surface quality for high-performance electromagnetic interference shielding applications

A Convenient and Efficient Path to Bead Foam Parts: Restricted Cell Growth and Simultaneous Inter-Bead Welding

Fabrication of flexible polyurethane/phosphorus interpenetrating polymer network (IPN) foam for enhanced thermal stability, flame retardancy and mechanical properties

Halogen‐free Intumescent Flame Retardancy and Mechanical Properties of the Microcellular Polypropylene with Low Expansion Ratio Via Continuous Extrusion Assisted by Subcritical CO 2

The Injected Foaming Study of Polypropylene/Multiwall Carbon Nanotube Composite with In Situ Fibrillation Reinforcement