Abstract:The construction of ceramic components with UV curing is a developing trend by an additive manufacturing (AM) technology, due to the excellent advantages of high precision selective fixation and rapid prototyping, the application of this technology to bone defect repair had become one of the hotspots of research. Hydroxyapatite (HAP) is one of the most popular calcium phosphate biomaterials, which is very close to the main ingredient of human bones. Thus, hydroxyapatite biomaterials are popular as bone graft materials. In summary, the preparation of HAP bioceramics by a 3D printing of digital light processing (DLP) is a promising work. However, the preparation of HAP hybrid suspensions with high solid loading and good fluidity that can be printed by DLP encountered some challenges. Therefore, the purpose of this work is to improve and develop a novel UV-curing suspension with a high solids loading, which the suspension with the hydrodynamic properties and stability are suitable for DLP printer, in order to compensate for the brittleness of HAP ceramics itself to a certain extent, a low amount of zirconia was added in the suspension as an additive to fabricate a zirconia toughened HAP bioceramic composite by a DLP of 3D printing. In this work, the HAP powder was pre-modified by two organic modifiers to improve the compatibility in the acrylic resin system, and the addition of the castor oil phosphate further reduced the shear stress of the suspension to ensure strong liquidity. The UV suspension with 60 wt% powder particle loading had a minimum viscosity of 7495 mPa·s at 30 rpm, which was vacuum sintered at 1100 °C, 1200 °C, and 1250 °C, respectively. The composite ceramics (with 6 wt% ZrO2) at 1200 °C had a relative density of 90.7%, while the sintered samples at 1250 °C had stronger tensile strength and bending strength. The toughening effect of zirconia incorporation on HAP ceramics was also confirmed by the change of tensile modulus and bending modulus, whereas the corresponding mechanical properties were also significantly enhanced.

A Novel ZrO2 Ceramic Suspension for Ceramic Stereolithography

Fabrication of Complex-Shaped Zirconia Ceramic Parts Via a DLP-stereolithography-based 3D Printing Method

Design of a Shaping System for Stereolithography with High Solid Loading Ceramic Suspensions

Preparation and stereolithography 3D printing of ultralight and ultrastrong ZrOC porous ceramics

Preparation of excellent performance ZTA ceramics and complex shaped components using digital light processing 3D printing technology

Optimized Zirconia 3D Printing Using Digital Light Processing with Continuous Film Supply and Recyclable Slurry System

Study of alumina ceramic parts fabricated via DLP stereolithography using powders with different sizes and morphologies

Development of a high solid loading β-TCP suspension with a low refractive index contrast for DLP -based ceramic stereolithography

Fabrication of High-Performance Al2O3-ZrO2 Composite by a Novel Approach That Integrates Stereolithography-Based 3D Printing and Liquid Precursor Infiltration

Advancements in DLP 3D Printing: High Strength Alumina Toughened Zirconia Ceramics for Biomedical Applications

Preparation of High-Stability Ceramic Slurry with Gel Behavior for Stereolithography 3D Printing

DLP 3D printing of high strength semi-translucent zirconia ceramics with relatively low-loaded UV-curable formulations

Additive Manufacturing and Characterization of Complex Al2o3 Parts Based on A Novel Stereolithography Method

Effect of high-speed sintering on the microstructure, mechanical properties and ageing resistance of stereolithographic additive-manufactured zirconia

Fused deposition fabrication of high-quality zirconia ceramics using granular feedstock

Fabrication and characterisation of ceramics via low-cost DLP 3D printing

Rapid and high-accuracy forming of ceramic parts by DLP technology based on optimization of shear stress

Zirconia UV-curable colloids for additive manufacturing via hybrid inkjet printing-stereolithography

Zirconia toughened hydroxyapatite biocomposite formed by a DLP 3D printing process for potential bone tissue engineering

Regulation of residual stress in stereolithography printing of ZrO2 ceramics

Reinforcement effect in printing precision and sintering performance for liquid crystal display stereolithography additive manufacturing of alumina ceramics