Abstract:Cr–Al-based oxynitride materials have attracted significant attention as hard protective coatings for decades. However, knowledge of the influence of the constituents on oxidation behavior is limited. Here, Cr–Al–O–N coatings with various Cr/Al ratios prepared using cathodic arc evaporation were studied with respect to their microstructure, mechanical properties, and oxidation behavior. With a decrease in the Cr/Al ratio, the coatings yielded a phase evolution from face-centered cubic CrN to rock salt-type cubic (Cr, Al) 2 O 3 to a wurtzite-type hexagonal AlN structure. The cubic structured coatings showed a comparable indentation hardness, much higher than that of the Cr-free Al–O–N coating with a wurtzite structure. Thermogravimetric together with differential scanning calorimetric (TG-DSC) analysis revealed that the ternary Cr–O–N and Al–O–N coatings were more susceptible to oxidation than the quaternary Cr–Al–O–N coatings. Moreover, isothermal oxidation experiments indicated that the addition of 66 at.% Al within the metallic species gives rise to the growth of an Al-rich oxide scale on top of the Cr–Al–O–N coating. However, this oxide scale containing substantial voids cannot prevent the underlying coating from oxidation. Oxidation kinetics study illustrates that the oxidation activation energies of (Cr x Al 1−x )–O–N coatings with x = 1.00, 0.76, 0.58, 0.33, and 0 are 252.3, 305.2, 370.7, 303.8, and 297.7 kJ/mol, respectively. The best oxidation resistance was obtained by the (Cr 0.58 Al 0.42 )–O–N coating, whereas the Al-containing (Cr 0.33 Al 0.67 )–O–N coating showed inferior oxidation resistance owing to its high intrinsic oxygen fraction.

Structure, Mechanical and Thermal Properties of Y-doped CrAlN Coatings

Influences of MCrAlY Coatings and TBCs on Oxidation Behavior of a Ni-Based Single Crystal Superalloy

Thermal and Thermo-Mechanical Properties of Ti–Al–N and Cr–Al–N Coatings

Effects of Yttrium Doping on High-Temperature Oxidation, Friction, and Wear Properties of CrAlN Films

Effects of High Al Content on the Phase Constituents and Thermal Properties in NiCoCrAlY Alloys

Stability of NiCrAlY coating/titanium alloy system under pure thermal exposure

Effect of Y on Microstructure and Properties of Al0.8FeCrCoNiCu0.5 High Entropy Alloy Coating on 5083 Aluminum by Laser Cladding

Effect of Cr on solidification structure and microhardness of Al-Ni alloy

Study on Microstructure and Oxidation Resistance Mechanism of Y-modified NiCrAlY Coating Prepared by Pack Cementation

Thermal-induced decomposition and mechanical properties of AlN/CrN superlattice coating

Structure, mechanical properties and thermal stability of CrAlNbN/TiN multilayers

Influence of Al Content on the Microstructure and Properties of the CrAlN Coatings Deposited by Arc Ion Plating

Comparative study on mechanical and tribological properties of Cr–Al–N and Cr–Al–O coatings deposited by cathodic arc evaporation

Investigation on the Microstructure and High-Temperature Properties of AlN Coating Through Oxygen Addition

Einfluss von Sc, Y, Ti, Zr, Hf, V, Nb und Ta auf strukturelle und mechanische Eigenschaften von Cr-Al-N-Schichten

Structure, mechanical and thermal properties of Ti1−x−y−zAlxTayBzN coatings

Microstructure, mechanical properties, and oxidation behavior of arc-evaporated Cr–Al–O–N coatings with various Cr/Al ratios

Mechanical and thermal properties of AlN/Ti1-xAlxN (x = 0, 0.45 and 0.62) multilayers

A First-Principles Study of Mechanical and Electronic Properties of Cr0.5-xAl0.5TMxN Hard Coatings (TM = Ti, V, Y, Zr, Hf, and Ta)

Microstructure, Corrosive‐Wear, and Electrochemical Properties of Laser Cladded NiCoCrAlY Coatings by Heat Treatment

Influence of Layer Number and Thickness of CrAlYN/CrAlYO Coatings on Phase Composition, Structure and Properties