Abstract:Cr–Al-based oxynitride materials have attracted significant attention as hard protective coatings for decades. However, knowledge of the influence of the constituents on oxidation behavior is limited. Here, Cr–Al–O–N coatings with various Cr/Al ratios prepared using cathodic arc evaporation were studied with respect to their microstructure, mechanical properties, and oxidation behavior. With a decrease in the Cr/Al ratio, the coatings yielded a phase evolution from face-centered cubic CrN to rock salt-type cubic (Cr, Al) 2 O 3 to a wurtzite-type hexagonal AlN structure. The cubic structured coatings showed a comparable indentation hardness, much higher than that of the Cr-free Al–O–N coating with a wurtzite structure. Thermogravimetric together with differential scanning calorimetric (TG-DSC) analysis revealed that the ternary Cr–O–N and Al–O–N coatings were more susceptible to oxidation than the quaternary Cr–Al–O–N coatings. Moreover, isothermal oxidation experiments indicated that the addition of 66 at.% Al within the metallic species gives rise to the growth of an Al-rich oxide scale on top of the Cr–Al–O–N coating. However, this oxide scale containing substantial voids cannot prevent the underlying coating from oxidation. Oxidation kinetics study illustrates that the oxidation activation energies of (Cr x Al 1−x )–O–N coatings with x = 1.00, 0.76, 0.58, 0.33, and 0 are 252.3, 305.2, 370.7, 303.8, and 297.7 kJ/mol, respectively. The best oxidation resistance was obtained by the (Cr 0.58 Al 0.42 )–O–N coating, whereas the Al-containing (Cr 0.33 Al 0.67 )–O–N coating showed inferior oxidation resistance owing to its high intrinsic oxygen fraction.

Thermal and Thermo-Mechanical Properties of Ti–Al–N and Cr–Al–N Coatings

Comparative study on mechanical and tribological properties of Cr–Al–N and Cr–Al–O coatings deposited by cathodic arc evaporation

Microstructure, mechanical properties, and oxidation behavior of arc-evaporated Cr–Al–O–N coatings with various Cr/Al ratios

Properties of TiAlCrN coatings prepared by vacuum cathodic arc ion plating

High Temperature Erosion Properties of Arc-Sprayed Coatings Using Various Cored Wires Containing Ti–Al Intermetallics

Structure, mechanical and thermal properties of Ti1−x−y−zAlxTayBzN coatings

Thermal Fatigue and Oxidation Resistance of TiAlN Coating Grown by Arc Ion Plating

Influence of Si and Ta mixed doping on the structure, mechanical and thermal properties of Ti Al N coatings

Effects of annealing temperature on the microstructure, mechanical and tribological properties of CrAlTiN coatings

Mechanical Properties of the TiAlSiN Coatings by Post Heat Treatments

Oxidation Resistance of （ti,al,cr）n Coatings at 800 ℃

Oxidation resistance of (Ti,Al,Cr)N coatings at 800 ℃

Mechanical properties, thermal stability and oxidation resistance of TiN/CrN multilayer coatings

Microstructure, Mechanical Properties, Wear and Erosion Performance of a Novel High Entropy Nitride (AlCrTiMoV)N Coating Produced by Cathodic Arc Evaporation

Growth, mechanical properties, and tribological performance of TiAlN/NbN and NbN/TiAlN bilayer coatings

On the high temperature oxidation behavior of AlCrBN/TiAlNbSiN multilayer coatings with addition of boron and silicon

EFFECT OF MCrAlY COATINGS ON OXIDATION RESISTANCE OF TiAl INTERMETALLICS

Mechanical and thermal properties of AlN/Ti1-xAlxN (x = 0, 0.45 and 0.62) multilayers

Thermostability, oxidation, and high-temperature tribological properties of nano-multilayered AlCrSiN/VN coatings

Evaluation of wear resistance of CrN, CrAlN, and TiAlN coatings deposited by multi-arc ion plating on spinning die of Cr12MoV

Structural, Mechanical, and Thermal Properties of the TiAlTaN/TiAlBN Multilayer