Abstract:Laser cladding, which is characterized by the minimal thermal impact on the substrate, is an advanced technique to restore the working dimensions of parts subject to wear. The Ni–Cr–B–Si system coatings can be used for parts operating at high temperatures. Our work aims at studying the effect of heating and subsequent cooling conditions in the process of high-temperature treatment on the features of the structural and phase state of the coating obtained by laser cladding of the PG-SR2 powder (chemical composition, wt %: 14.8 Cr, 2.1 B, 2.9 Si, 2.6 Fe, and 0.48 S; the rest is Ni) and the properties obtained as a result of this treatment (hardness and tribological characteristics in sliding on fixed abrasive corundum). Samples with a laser-clad layer were heated at a temperature of 1050°C (holding for 1 h) and subsequently cooled in water (which made it possible to record structural transformations under high-temperature heating), in air, and in a muffle and a vacuum furnace. It has been shown that the rate of cooling during the high-temperature treatment of the laser-clad PG-SR2 coating significantly affects the structure and properties. High-temperature heating leads to partial diffusive dissolution of nickel borides (Ni 3 B) and chromium carbides (Cr 23 C 6 ) in a solid solution and a corresponding decrease in hardness and an increase in the abrasive wear intensity and the coefficient of friction. The reduction in the rate of cooling from 1050°C of the samples in air, a muffle furnace, or a vacuum furnace leads to the precipitation of chromium borides (CrB) and nickel silicide (Ni 3 Si), which were absent in the clad coating structure. High-strength CrB borides whose hardness is equal to or even exceeds that corundum abrasive hinder the development of the microcutting mechanism in the process of abrasive wear. Coarse chromium carbides and borides formed in the process of slow cooling in the furnace form wear-resistant framelike structures. This results in an increase in hardness and abrasive wear resistance to the values that exceed those of the original clad coating.

Microstructure, Corrosive‐Wear, and Electrochemical Properties of Laser Cladded NiCoCrAlY Coatings by Heat Treatment

Effect of Heat Treatment on Microstructure and Tribocorrosion Performance of Laser Cladding Ni-65 WC Coating

Effect of Heat Treatment on Microstructure and Wear Behavior of Laser Clad FeCoCrMoNi High-Entropy Alloy Coatings

Effect of Conditions of High-Temperature Treatment on the Structure and Tribological Properties of Nickel-Based Laser-Clad Coating

Microstructure, corrosive-wear and electrochemical performance of laser cladded NiTi–xAl 2 O 3 coatings in 3.5%NaCl solution

Enhanced Corrosion Resistance of High Speed Laser-Cladded Ni/316l Alloy Coating by Heat Treatment

Influence of heat treatment on laser clad Ta reinforced NiCrBSi coating

Influence of Heat Treatment on Microstructure and Mechanical Properties of Laser Cladding Coatings

Thermal Stability and Hot Corrosion Performance of the AlCoCrFeNi2.1 High-Entropy Alloy Coating by Laser Cladding

Effects of Thermal Treatment on Microstructure and Wear Properties of Ni60/CeO2 Composite Coating 35CrMoV Steel by Laser Cladding

Effect of Temperature and Load on Tribological Behavior in Laser-Cladded FeCrSiNiCoC Coatings

Effect of Laser Cladding Layers on Microstructure and Mechanical Properties of NiCoCrAlY Bond Coat

Microstructure, thermostability and tribological behavior of composite CoCrFeNiTix high-entropy alloy coatings fabricated by laser cladding

Microstructure, microhardness and corrosion resistance of laser cladding Ni–WC coating on AlSi5Cu1Mg alloy

Interface Microstructure and High Temperature Corrosion of Nano-Al2O3 Particle Reinforced Ni-based Alloy Powder Laser Cladding

Microstructure and Oxidation Resistance of the Laser-Clad Co22Cr12Al0.7Y Alloys

Tribological Performance and Wear Mechanism of Laser Cladded NiCrAl-WC Coatings at High-Temperature

The microstructure and tribological characteristics of laser-clad Ni–Cr–Al coatings on aluminium alloy

Mechanical and Tribological Properties of Fe- and Ni-based Coating Material under Laser Cladding Process

Effects of Heat Treatment on Microstructure and Wear Behavior of Modified Aluminum Bronze Coatings Fabricated by Laser Cladding

Microstructure and Abrasive-wear Behavior Under High Temperature of Laser Clad Ni-based WC Ceramic Coating