Abstract:Direct conversion receiver (DCR) architecture is a promising candidate in the radio frequency (RF) front end because of its low power consumption, low cost and ease of integration. However, flicker noise and direct current (DC) offset are large issues. Owing to the local oscillator (LO) frequency, which is half of the RF frequency, and the absence of a DC bias current that introduces no flicker noise, the subharmonic passive mixer (SHPM) core topology front end overcomes the shortcoming effectively. When more and more receivers (RX) and transmitters (TX) are integrated into one chip, the linearity of the receiver front end becomes a very important performer that handles the TX and RX feedthrough. Another reason for the requirement of good linearity is the massive electromagnetic interference that exists in the atmosphere. This paper presents a linearity-improved RF front end with a feedforward body bias (FBB) subharmonic mixer core topology that satisfies modern RF front end demands. A novel complementary derivative superposition (DS) method is presented in low noise amplifier (LNA) design to cancel both the third- and second-order nonlinearities. To the best knowledge of the authors, this is the first time FBB technology is used in the SHPM core to improve linearity. A Volterra series is introduced to provide an analytical formula for the FBB of the SHPM core. The design was fabricated in a 0.13 μm complementary metal oxide semiconductor (CMOS) process with a chip area of 750 μm × 1270 μm. At a 2.4 GHz working frequency, the measurement result shows a conversion gain of 36 dB, double side band (DSB) noise figure (NF) of 6.8 dB, third-order intermodulation intercept point (IIP3) of 2 dBm, LO–RF isolation of 90 dB and 0.8 mW DC offset with 14.4 mW power consumption at 1.2 V supply voltage. These results exhibit better LO–RF feedthrough and DC offset, good gain and NF, moderate IIP3 and the highest figure of merit compared to the state-of-the-art publications.

Design Trade-Offs For Digitally Equalized Cmos Rf Transmitter

High-Linearity Direct Conversion Receiver with the Transconductance Equalization Technique and DCOC Method

A CMOS 135–150 GHz 0.4 dBm EIRP transmitter with 5.1dB P1dB extension using IF envelope feed-forward gain compensation

A High Performance 2-Ghz Direct-Conversion Front End with Single-Ended RF Input in 0.13 Um CMOS

The Design of All-Digital Polar Transmitter Based on ADPLL and Phase Synchronized ΔΣ Modulator

A 21dBm-OP1dB 20.3%-Efficiency-131.8dBm/Hz-Noise X-Band Cartesian-Error-Feedback Transmitter with Fully Integrated Power Amplifier in 65nm CMOS

28.8 A 21dBm-OP<inf>1dB</inf> 20.3%-Efficiency -131.8dBm/Hz-Noise X-Band Cartesian-Error-Feedback Transmitter with Fully Integrated Power Amplifier in 65nm CMOS

Design and Optimization of a Milli-Meter Wave Amplifier Using Nano-Scale CMOS Devices

A 21-Dm-op 1 Db 20.3%-Efficiency −131.8-Dbm/hz-noise $X$ -Band Cartesian Error Feedback Transmitter with Fully Integrated Power Amplifier in 65-Nm CMOS

Digitally Equalized CMOS Transmitter Front-End with Integrated Power Amplifier

Cmos Rf Transmitter With Integrated Power Amplifier Utilizing Digital Equalization

Adaptive digital techniques for efficiency and linearity enhancement of CMOS RF power amplifiers

A Novel Low-Noise High-Linearity CMOS Transmitter for Mobile UHF RFID Reader

Cmos Integrated Low Tx Noise Digital Transmitter with Tunable Directional Coupler for High Performance Uhf Rfid Reader

A 10Gb/s analog equalizer in 0.18um CMOS

A Linearity Improvement Front End with Subharmonic Current Commutating Passive Mixer for 2.4 GHz Direct Conversion Receiver in 0.13 Μm CMOS Technology

A LOW POWER, HIGH-LINEARITY CMOS DOWNCONVERSION FOLDED MIXER FOR 2.4GHz ISM BAND APPLICATIONS

A Modulation Depth and Output Power Tunable 5.8-Ghz Cmos Direct-Conversion Transmitter

Design Technique of CMOS Mixer

A Novel Cmos Transmitter Front-End For Mobile Rfid Reader

An All-Digital Quadrature Rf Transmitter Front-End Using 3-Bit Sigma Delta Modulators In 65-Mm Cmos