Abstract:Concrete-filled steel tubes (CFST) incorporating high-strength steel (HSS) could produce more efficient structural system with lighter weight and higher capacity. However, the design methods for applying concrete-filled highstrength steel tubes (CFHST) are not available yet and limited investigations had been reported. In this research, 8 full scale mid-slenderness circular CFHST specimens, made of innovative high-performance Q460qENH structural steel with actual yielding stress fy as high as 530 MPa, were tested subject to axial and eccentric compression. The main parameters considered in the experimental program included: (a) infilled concrete strength fc' = 39.8-75.3 MPa and (b) loading eccentricity ratio e/D = 0-0.3. The numerical model for CFHST was established and validated with load-displacement curves, failure modes and neutral axis locations obtained from the 8 experiments. The numerical models were further validated in capacity predictions with 232 axial compressions and compression-bending CFHST experimental data collected from the literature, proved to be generally applicable with fy = 435-835 MPa, xi = 0.5-8.5 and lambda n = 0.07-1.90 in both circular and square sections. Based on the validated numerical models, total 526 simulations were performed to investigate the influence of: (a) higher yielding strength fy and thinner-walled steel tubes; (b) confinement factor xi and (c) normalized slenderness ratio lambda n, on the composite strength fsc and compression-bending (N-M) interaction behavior. Experimental and numerical investigations showed that high strength steel could further improve the CFST capacity with basically no reduction in safety margin and ductility performance, but was in need of design method modifications due to changes in composite mechanism. On this basis, an analytical refined plastic-section equilibrium model (RPE model) was proposed to derive practical N-M interaction design curve with consideration of strength enhancement due to the composition and actual stress distribution at ultimate state. The further proposed general design method for compression-bending CFHST included: (a) formulas of fsc-xi relationship; (b) validated formulas of pure-bending capacity and overall stability inherited from GB 50936; (c) practical design curves of N-M interaction considering the effect of xi and lambda n. By comparing with GB 50936, AISC 360, EC 4 and CECS 28 provisions, the proposed method provided more accurate solutions in capacity predictions of CFHST members.

Experimental Studies On The Strength With High Slenderness Ratio Concrete Filled Steel Tubular Columns

Seismic Behavior of Concrete-Filled Wide Rectangular Steel Tubular (CFWRST) Stub Columns

Experimental investigation of concrete-filled steel tubular columns with reinforcing lattice angle

Experimental Study on Axial Compressive Behavior of Concrete-Filled Corrugated Steel Tubular Columns

Tests on Concrete Filled Steel Tubular Columns with High Slenderness Ratio

Experimental Investigation And Design Of Concrete-Filled Cold-Formed Thin-Walled Steel Tubes Subject To Bending

Experimental Investigation and Design of Thin- Walled Concrete-Filled Steel Tubes Subject to Bending

08.17: Experimental Behaviour of High‐strength Thin‐walled Concrete Filled Steel Tubular Stub Columns

Experimental Behaviour of Concrete-Filled Stiffened Thin-Walled Steel Tubular Columns

Behavior of Eccentrically Loaded Large-Scale CFST Slender Columns with Latticed Annular Steel

Experimental investigation of thin-walled concrete-filled steel tube columns with reinforced lattice angle

Experimental and Numerical Investigations on Concrete-Filled Double-Tubular Slender Columns under Axial and Eccentric Loading

Behaviour of Short and Slender Concrete-Filled Stainless Steel Tubular Columns

Experimental Investigations on Axial–Flexural Behaviour of Slender Concrete Filled Steel Tubular Columns

Experimental study on square concrete-filled double skin steel tubular short columns

Experimental and numerical investigation of square concrete-filled double-skin steel stiffened tubular stub columns with CHS inner tubes under axial compression

Experiments on Special-Shaped CFST Stub Columns under Axial Compression

Experimental Investigation of Special-Shaped Concrete-Filled Square Steel Tube Composite Columns with Steel Hoops under Axial Loads

Experimental behaviour of slender circular concrete-filled stainless steel tubular columns under axial compression

Experimental and numerical behavior of eccentrically loaded square concrete-filled steel tubular long columns made of high-strength steel and concrete

Behavior and General Design Method of Concrete-Filled High-Strength Steel Tube (CFHST) Columns