Abstract:ABSTRACTDeveloped more than 80 years ago, the design procedure of concrete filled steel tubes (CFST) has several limitations that can still be found in most current international design standards. The two main limitations that present themselves are the lack of ability to achieve material enhancement when using high strength materials and restrictions on the geometry of the steel tube thickness to the overall column diameter. This geometric limitation is placed on the design to ensure that the steel tube remains ‘compact’. In complying with these constraints it is assumed in the design equations that local buckling of the steel tube will not take place before the ultimate global buckling load is achieved.With the introduction of higher strength materials, specifically when dealing with steel, the strength increase leads to the design of sections with increased slenderness. As the section becomes more slender, the ability to maintain the compact section limitations in the design codes becomes increasingly difficult. This paper looks at an experimental study on very thin‐walled steel tubes filled with high‐strength concrete and how localised buckling affects their compressive capacity.Adopting a diameter to thickness ratio of 200, 24 circular tubes were constructed using a high‐strength cold‐formed steel sheet, with yield stresses above 500MPa and filled with 100MPa concrete. Employing both thin‐walled sections and high strength materials, the effects of localised buckling in these composite members when subjected to compression has been studied. The experimental programme explored four main conditions; when both the steel and concrete were loaded and bonded together, when the concrete core inside the CFST was loaded, when the steel tube in the CFST was loaded and when the concrete core without the steel tube was tested.By studying the failure modes of both the concrete and the steel tube when acting compositely and individually, the experimental work shows that there is valid evidence to support the theory that even when using high strength materials in slender sections, confinement to the concrete core is provided. Finally, the results of the experimental work have been compared to the compressive design capacities predicted by current international design codes, showing that these provisions are conservative.

Experimental Investigations on Axial–Flexural Behaviour of Slender Concrete Filled Steel Tubular Columns

Experimental Study on Axial Compressive Behavior of Concrete-Filled Corrugated Steel Tubular Columns

Combined Axial and Flexural Behavior of Concrete-Filled Corrugated Steel Tubular Columns

Experimental and Numerical Investigations on Concrete-Filled Double-Tubular Slender Columns under Axial and Eccentric Loading

Behavior of Eccentrically Loaded Large-Scale CFST Slender Columns with Latticed Annular Steel

Experimental Investigation and Design of Thin- Walled Concrete-Filled Steel Tubes Subject to Bending

Behavior and Design of Concrete-Filled Narrow Rectangular Steel Tubular (CFNRST) Stub Columns under Axial Compression

Experimental Studies On The Strength With High Slenderness Ratio Concrete Filled Steel Tubular Columns

Experimental Investigation And Design Of Concrete-Filled Cold-Formed Thin-Walled Steel Tubes Subject To Bending

Experimental and numerical studies of axially loaded square concrete‐encased concrete‐filled large‐diameter steel tubular short columns

Behavior and design of axially loaded square concrete-filled double steel tubular slender columns

08.17: Experimental Behaviour of High‐strength Thin‐walled Concrete Filled Steel Tubular Stub Columns

Investigation of axial-flexural behaviour of concrete-encased concrete-filled steel tube slender beam–columns

Experiments on Special-Shaped CFST Stub Columns under Axial Compression

Compressive Behaviour of Diagonally Stiffened Concrete Filled Steel Tubular Stub Columns with Reinforcement Stiffeners

Numerical investigation and design of concrete-filled double square steel tube columns under axial compression

Compressive behavior of concrete-filled steel tubular columns with internal high-strength steel spiral confinement

Axial Compression Behaviour of Circular Concrete-Filled Stainless-Clad Bimetallic Steel Tubular Stub Columns

Experimental behavior of concrete-filled double-skin tubular columns with outer galvanized corrugated steel tubes under axial compression

Circular Concrete-Encased Concrete-Filled Steel Tube (cfst) Stub Columns Subjected to Axial Compression

Axial Loading Behaviour of Self-Compacting Concrete-Filled Thin-Walled Steel Tubular Stub Columns