Abstract:ABSTRACTDeveloped more than 80 years ago, the design procedure of concrete filled steel tubes (CFST) has several limitations that can still be found in most current international design standards. The two main limitations that present themselves are the lack of ability to achieve material enhancement when using high strength materials and restrictions on the geometry of the steel tube thickness to the overall column diameter. This geometric limitation is placed on the design to ensure that the steel tube remains ‘compact’. In complying with these constraints it is assumed in the design equations that local buckling of the steel tube will not take place before the ultimate global buckling load is achieved.With the introduction of higher strength materials, specifically when dealing with steel, the strength increase leads to the design of sections with increased slenderness. As the section becomes more slender, the ability to maintain the compact section limitations in the design codes becomes increasingly difficult. This paper looks at an experimental study on very thin‐walled steel tubes filled with high‐strength concrete and how localised buckling affects their compressive capacity.Adopting a diameter to thickness ratio of 200, 24 circular tubes were constructed using a high‐strength cold‐formed steel sheet, with yield stresses above 500MPa and filled with 100MPa concrete. Employing both thin‐walled sections and high strength materials, the effects of localised buckling in these composite members when subjected to compression has been studied. The experimental programme explored four main conditions; when both the steel and concrete were loaded and bonded together, when the concrete core inside the CFST was loaded, when the steel tube in the CFST was loaded and when the concrete core without the steel tube was tested.By studying the failure modes of both the concrete and the steel tube when acting compositely and individually, the experimental work shows that there is valid evidence to support the theory that even when using high strength materials in slender sections, confinement to the concrete core is provided. Finally, the results of the experimental work have been compared to the compressive design capacities predicted by current international design codes, showing that these provisions are conservative.

Behaviour of Short and Slender Concrete-Filled Stainless Steel Tubular Columns

Experimental behaviour of slender circular concrete-filled stainless steel tubular columns under axial compression

Behaviour of Slender Square Concrete-Filled Stainless Steel Columns Subject to Axial Load

Behavior and Design of Slender Concrete-Filled Wide Rectangular Steel Tubular Columns under Axial Compression

Experimental Studies On The Strength With High Slenderness Ratio Concrete Filled Steel Tubular Columns

Experimental Behaviour of Concrete-Filled Stiffened Thin-Walled Steel Tubular Columns

Tests on Concrete Filled Steel Tubular Columns with High Slenderness Ratio

Experimental investigation of concrete-filled steel tubular columns with reinforcing lattice angle

Behavior of Eccentrically Loaded Large-Scale CFST Slender Columns with Latticed Annular Steel

Experimental behaviour of high performance concrete-filled steel tubular columns

Experimental Study on Axial Compression Performance of Thin-Walled Steel Tube Lightweight Concrete Columns With Composite Section

08.17: Experimental Behaviour of High‐strength Thin‐walled Concrete Filled Steel Tubular Stub Columns

Experimental Behavior of Concrete-Filled Stainless Steel Tubular Columns under Cyclic Lateral Loading

Behaviour Of Concrete-Filled Square Steel Tubular Columns With Stiffeners Under Concentric Compression

Analysis and Design of Concrete-Filled Stiffened Thin-Walled Steel Tubular Columns under Axial Compression

Tests and Numerical Simulation on Short Composite-Sectioned Concrete Filled Steel Tubular Columns Subjected to Axial Compressive Loading

Experimental and numerical behavior of eccentrically loaded square concrete-filled steel tubular long columns made of high-strength steel and concrete

Axial Compression Behaviour of Circular Concrete-Filled Stainless-Clad Bimetallic Steel Tubular Stub Columns

Axially Compressive Behaviors Of High-Strength Concrete-Filled Shc Steel Tubes

Behavior and design of axially loaded square concrete-filled double steel tubular slender columns

Experimental study on square concrete-filled double skin steel tubular short columns