Abstract:Bi2Te3-based compounds are currently the most commercially relevant thermoelectric materials near room temperature. They are prepared via hot pressing, hot deformation, spark plasma sintering, and other consolidation processes, which are typically performed at 400–500 °C. Such high-temperature processes are energy-intensive and generate unnecessary waste heat, making them undesirable for a large-scale production. In this study, a low-temperature liquid-phase-assisted sintering (or so-called cold-sintering) process was employed to fabricate p-type Bi0.5Sb1.5Te3 bulk materials at temperatures below 150 °C. At the optimal sintering temperature (130 °C), a ZT value as high as 0.56 at 450 K can be achieved, competitive to that of a commercial Bi0.5Sb1.5Te3 ingot (ZT 0.8–1.0). The addition of a small amount of transient liquid facilitates grain reorientation and expedites a mass transfer process under axial compaction and liquid evaporation conditions, thus resulting in nearly fully densified Bi0.5Sb1.5Te3 pellet samples (>97% theoretical density). Furthermore, the low-temperature sintering process results in the reduction of grain size and promotes twin boundaries, resulting in a low lattice thermal conductivity of 0.57 W m–1 K–1 at 380 K due to phonon scattering. The strategy reported in this work can be used not only as a substitute for high-temperature sintering of other thermoelectric materials but also to engineer phonon scattering for high-performance thermoelectrics.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c03540.Single parabolic band model and calculated transport properties; EBSD analysis for pellet sintered at 110 °C; BSE, EDS mapping, and TEM images of pellet sintered at 130 °C; average ZT values; and XPS results (PDF)This article has not yet been cited by other publications.

Enhanced Thermoelectric Performance of Nanocrystalline Indium Tin Oxide Pellets by Modulating the Density and Nanoporosity Via Spark Plasma Sintering

Enhanced thermoelectric performance of n -type PbTe bulk materials fabricated by semisolid powder processing

Microstructure and thermoelectric properties of porous Bi 2 Te 2.85 Se 0.15 bulk materials fabricated by semisolid powder processing

Interface driven energy filtering of thermoelectric power in spark plasma sintered Bi(2)Te(2.7)Se(0.3) nanoplatelet composites.

Enhanced performance of thermoelectric nanocomposites based on Cu12Sb4S13 tetrahedrite

Lead-free AgSn4SbTe6 Nanocomposites with Enhanced Thermoelectric Properties by SiC Nanodispersion

Nanocrystalline Thermoelectric Ca3Co4O9 Ceramics by Sol−Gel Based Electrospinning and Spark Plasma Sintering

Fabrication of Nanostructured Non-Stoichiometric TiO2-x by Spark Plasma Sintering for Enhancing Its Thermoelectric Properties

Tailoring Nanoporous Structures in Bi2Te3 Thin Films for Improved Thermoelectric Performance

(Bi,sb)2te3/sic Nanocomposites with Enhanced Thermoelectric Performance: Effect of SiC Nanoparticle Size and Compositional Modulation

Microstructure Composite-Like Bi2s3 Polycrystals With Enhanced Thermoelectric Properties

Enhanced thermoelectric and mechanical properties of Bi0.5Sb1.5Te3 alloy with dispersed yttrium oxide ceramic nanoparticles

Nanoporous PbSe–SiO2 Thermoelectric Composites

Enhanced Thermoelectric Performance of Xmos2–tis2 Nanocomposites

Cold-Sintered Bi 2 Te 3 -Based Materials for Engineering Nanograined Thermoelectrics

Enhanced Thermoelectric Performance of In2O3-based Ceramics Via Nanostructuring and Point Defect Engineering.

Optimized Hetero-Interfaces by Tuning 2d Sns2 Thickness in Bi2te2.7se0.3/Sns2 Nanocomposites to Enhance Thermoelectric Performance

Synthesis of Nanocomposites with Improved Thermoelectric Properties

Enhanced Thermoelectric Performance of GeTe-Based Composites Incorporated with Fe Nanoparticles

Realization of an Ultrahigh Power Factor and Enhanced Thermoelectric Performance in TiS2 Via Microstructural Texture Engineering.

Nanostructured Bi2-Xcuxs3 Bulk Materials With Enhanced Thermoelectric Performance