Abstract:This Ph.D. research is based on the development of novel sol-gel techniques for synthesis of nanostructured ultra high temperature ceramics (UHTCs) and subsequent spark plasma sintering (SPS) for densifying the UHTC composites. The liquid nature of the sol-gel process offers advantages such as high purity and ability for mixing and infiltration, and thus it can overcome some shortcomings of the conventional power processing of ceramics. SPS delivers microstructures with good density and fine grain size due to its internal heat generation, high heating rate and short sintering time required. Titanium carbide (TiC) and zirconium diboride (ZrB₂) are selected as the UHTC matrix materials to form composites with different kinds of carbon based materials, including 1D carbon nanotubes (CNTs), 1D chopped carbon fibers, 2D woven and 3D needle-punched carbon fiber fabrics, and 3D graphene networks. One challenge to form the composites by conventional powder processing is the difficulty to achieve a homogeneous mix of ceramic powders and the carbon materials. The aim of this research is to take the advantages of sol-gel processing to synthesize nanostructured carbon reinforced UHTC composites with improved microstructures, mechanical and/or other properties. Graphene/TiC composites were synthesized through sol-gel infiltration of graphene network sponges. The C/Ti ratio of the sol-gel solutions influenced the composition as well as the microstructure of the composites. Graphene sheets could react with titanium dioxide (TiO₂) during the carbothermal reduction, forming a plate-like structure when the carbon content in the sol was low. The samples after SPS sintering showed interesting microstructures of nanostructured TiC surrounded by a network of graphene sheets. The composites were toughened by debonding and bridging of the graphene sheets. It was also proved that the composites exhibited an energy absorption mechanism under impact. CNT/TiC composites were prepared by sol-gel mixing and SPS sintering. The application of sol-gel gave an advantage in homogenous mixing. CNTs were able to toughen the composite by bridging, pullout and crack deflection. The fracture toughness increased with the amount of CNTs, but sacrificing the hardness of the materials. A CNTs containing TiC based sol was coated on ZrB₂ raw powders, forming a homogeneous microstructures after sintering, where most of the TiC grains and CNTs were distributed at the grain boundaries of ZrB₂, forming weak interfaces, which benefited the toughness through crack deflection and impact absorption. The chopped carbon fibers had similar toughening effect to CNTs in the composites. Different types of coatings on the surface of carbon fibers influenced the interface properties between ceramic matrix and fibers, thus affecting the fiber pullout and debonding. Sol-gel infiltration was applied to synthesize ceramic composites with 2D woven and 3D needle-punched carbon fiber fabrics. The results showed that sol-gel infiltration was a much more effective way to uniformly fill the fine pores between fiber filaments than the conventional powder slurry infiltration method. The composites showed improved fracture toughness as a result of fiber pullout, debonding, and crack deflection.

Nanocrystalline Thermoelectric Ca3Co4O9 Ceramics by Sol−Gel Based Electrospinning and Spark Plasma Sintering

Nanocrystalline Structure and Thermoelectric Properties of Electrospun Naco2o4 Nanofibers

Preparation of Ca3co4o9 and Improvement of Its Thermoelectric Properties by Spark Plasma Sintering

FABRICATION AND THERMOELECTRIC PROPERTIES OF Ca_3Co_4O_9 CERAMICS

High‐performance thermoelectric calcium cobaltite nanoribbon ceramic via electrospinning and dual spark plasma texturing

Lead-free AgSn4SbTe6 Nanocomposites with Enhanced Thermoelectric Properties by SiC Nanodispersion

Thermoelectric Performance of Zn and GeCo-Doped In2O3 Fine-Grained Ceramics by the Spark Plasma Sintering

Enhanced Thermoelectric Properties of Nano-Sic Dispersed NaCo2O4 Composites

Thermoelectric Performance of Zn and Ge Co-Doped In2o3 Fine-Grained Ceramics by the Spark Plasma Sintering

High-temperature Electrical Transport Behaviors in Textured Ca3Co4O9-based Polycrystalline Ceramics

Enhancing the thermoelectric performance of cold sintered calcium cobaltite ceramics through optimised heat-treatment

Enhanced performance of thermoelectric nanocomposites based on Cu12Sb4S13 tetrahedrite

Preparation of Ca3Co4O9 by Polyacrylamide Gel Processing and Its Thermoelectric Properties

Synthesis of Nanocomposites with Improved Thermoelectric Properties

Electro-Thermo-Magnetic Effect-Induced Large Thermoelectric Performance of Calcium Cobaltite Nanocomposites

Nanostructure Engineering and Performance Enhancement in Fe2O3-Dispersed Cu12Sb4S13 Thermoelectric Composites with Earth-Abundant Elements.

High Thermoelectric Performance of Nanostructured In2O3‐Based Ceramics

Synthesis of Highly Textured Ca3co4o9 Ceramics by Spark Plasma Sintering

High Temperature Thermoelectric Properties of Oxide Ca2co2o5

Sol-gel synthesis of carbon based materials reinforced ultra high temperature ceramic composites

Thermoelectric Properties of the Ca3Co4O9 Ceramics by K+ Substitution