Abstract:White-light OLED devices play an important application in information display fields. Optical interference of the microcavity structure has an important effect on device performances. According to the design of the band structure, ITO/MoO3 composite films were used as the anode, and Mg : Ag (1%) composite films were prepared by coevaporation as the translucent cathode; CuPc was used as the hole injection layer and anode passivation layer, NPB as the hole transmission layer and yellow light main material, rubrene as yellow dopant material, ADN as blue light main material, DSA-Ph as blue dopant material, and TPBi and Alq3 as the electron transport layers. We realized the change of the microcavity structure by adjusting the thickness of each organic functional layer film and simulated and calculated the optimized thickness of each organic film layer and influence on OLED device performances using the SimOLED software system. The optimized OLED microdisplay structure is Si(CMOS)/ITO (35 nm)/MoO3 (2 nm)/CuPc (5 nm)/2-TNATA (20 nm)/NPB (10 nm)/NPB : rubrene (1.5%)ADN : DSA-Ph (5%) (25 nm)/TPBi (15 nm)/Alq3 (1.2 nm)/Mg (13 nm) : Ag (1%). The optimized OLED microdisplay was prepared by the vacuum coating system, and the photoelectric performances of the OLED device were characterized by a spectral testing system consisting of the Photo Research PR655 spectrometer and Keithley 2400 program-controlled power supply. The effect of the microcavity structure on OLED device performances was studied. The results show that the variation of the film thickness of each organic functional layer has an important effect on the performances of OLED microdisplay, such as brightness and color coordinate, and the OLED microdisplay reaches a higher brightness of 3342 cd/m2 under the normal working voltage at 5.0 V after the structure is optimized, with CIE coordinate (0.28, 0.37), which is closer to the energy point of standard white light.

Pmoled Micro Display And Performance Enhancing

Efficient Mini/Micro-Perovskite Light-Emitting Diodes

Controller/driver chip for 65k color PM-OLED

Microscale Perovskite Quantum Dot Light‐Emitting Diodes (Micro‐PeLEDs) for Full‐Color Displays

Towards Micro-Peled Displays

All Silicon Microdisplay Fabricated Utilizing 0.18 μm CMOS-IC With Monolithic Integration

A New Pixel Circuit for Micro-Light Emitting Diode Displays with Pulse Hybrid Modulation Driving and Compensation

A Fully-Integrated Micro-Display System With Hybrid Voltage Regulator

P‐11.5: Realization of High PPI Transparent TFT Backplane and Its Application in Micro‐LED Display

Ultra-small Size Micro-LEDs with Enhanced Efficiency for Near-Eye Display

18.5: High Performance Transparent Micro‐LED Display

3400 PPI Active-Matrix Monolithic Blue and Green Micro-LED Display

P‐9: Student Poster: Two‐Mode PWM Driven Micro‐LED Displays with Dual‐Gate Metal‐Oxide TFTs

16‐2: A 4‐inch Full Color Active‐matrix Mini‐LED Display Based on 0408 Chip and 500um Pixel

P‐9.14: High transparent Active matrix Mini‐LED Full Color Display with IGZO TFT Backplane

Extremely high pixel density color conversion micro-LED displays with high efficiency and wide color gamut coverage

P‐124: Efficiency Enhanced Top Emitting OLED‐on‐Silicon Microdisplay with Aluminum Anode

9‐4: Late‐News Paper: Full Color Organic Light Emitting Diodes on Silicon Micro‐display with Ultra‐high Luminescence and High Resolution

Ultrahigh-Efficiency Green Pholeds With A Voltage Under 3 V And A Power Efficiency Of Nearly 110 Im W-1 At Luminance Of 10 000 Cd M(-2)

Design Simulation and Preparation of White OLED Microdisplay Based on Microcavity Structure Optimization

92‐3: 1.63‐inch 403‐PPI Full‐color Active‐matrix LTPS Micro‐LED Display