Abstract:The rod-fastened rotor is comprised of a series of discs damped together by a central tie rod or several tie rods on the pitch circle diameter. The equivalent flexural stiffness of contact interfaces in the rod-fastened rotor is the key concern for accurate rotor dynamic performance analysis. Each contact interface was modeled as a bending spring with stiffness of K-e and a hinge in this study. The contact states of the contact interfaces which depend on the pre-tightening forces and bending moments (static) have effects on K-c. The approach to calculating K-e in two contact states is presented. The first contact state is that the whole zone of the contact interface is in contact, K-e is determined by the contact layer which consists of asperities of the contact surfaces. Hertz contact theory and the GW (Greenwood and Williamson) statistical model are used to calculate the equivalent flexural stiffness of the contact layer Kce. The second contact state is that some zones of the contact interface are separated (when the bending moment is relative large), the equivalent flexural stiffness of the rotor segment Ksf (not include Kc) decreases as the material in the separated zone has no contribution to the bending load carrying capacity of the rotor The strain energy which is calculated by the finite element method (FEM) is used to determine K-sf. The stiffness Ksf is equivalent to the series stiffness of the discs of the rotor segment with flexural stiffness of K-d and a spring with bending stiffness of K-cc in the location of the contact interface, so K-e is equal to the series stiffness of K-ee and K-cf in the second contact state. The results of a simplified rod-fastened rotor indicate that for a flied pre-tightening force, K-ee decreases with bending moments in the first contact state whereas increases with bending moments in the second contact state. In addition, K-c and K-c decreases abruptly with the increase of bending moments in the second contact state when the rotor is subjected to a relatively large pre-tightening force. Finally, the multipoint exciting method was used to measure the modal parameters of the experimental rod-fastened rotor It is found that the experimental modal frequencies decrease as the pre-tightening force decreases.

Model Updating and Global Eigenvalue Analysis of a Tie-Bolt Rotor Using Zero-Length Contact Elements under Different Preloads

Determination of Contact Stiffness and Damping of a Tie-Bolt Rotor with Interference Fits Using Model Updating with Thin-Layer Elements

Modeling a Two-Span Rotor System Based on the Hamilton Principle and Rotor Dynamic Behavior Analysis

Rotor Dynamic Analysis of Tie-Bolt Fastened Rotor Based on Elastic-Plastic Contact

Modal Frequency and Stability of Rotor System Supported by Viscoelastic Elastomeric Dampers

Dynamic Modeling of Tie-bolt Rotors via Fractal Contact Theory and Virtual Material Method

Dynamic modeling and stability analysis of a rotor-bearing system with bolted-disk joint

A Simple Contact Model for Simulating Tie Bolt Rotor Butt Joints With and Without Pilot Fits

Thin-layer element method for multi-stage rotor bolt loosening identification

Nonlinear Dynamic Analysis for a Jeffcott Rotor Considering Varying Connection Stiffness of Bolted Joint

Dynamics of a Rod-Fastened Rotor Considering the Bolt Loosening Effect

Numerical and experimental analysis of the effect of eccentric phase difference in a rotor-bearing system with bolted-disk joint

Numerical Studies on Time-Varying Stiffness of Disk-Drum Type Rotor with Bolt Loosening

Numerical and experimental investigations on dynamic behaviors of a bolted joint rotor system with pedestal looseness

Measured and investigated nonlinear dynamics parameters on bolted flange joints of combined rotor

Modal Analysis for a Rod-Fastened Rotor Considering Contact Effect Based on Double Fractal Model

Nonlinear Dynamic Behaviors and Stability of Circumferential Rod Fastening Rotor System

Methods for Modeling Stiffness and Model Updating for the Rod-fastened Rotor of Gas Turbine

Analysis of Bolt Preload Mistuned Model and Its Impact on Stress Distribution of Curvic Couplings

Dynamic Modeling and Analysis of Distributed Rod Fastening Rotor

Effects Of Bending Moments And Pre-Tightening Forces On The Flexural Stiffness Of Contact Interfaces In Rod-Fastened Rotors