Abstract:Laser remelting (LR) is often used during selective laser melting (SLM) processes to improve the densification degree and top surface quality of the products. However, researches regarding its effects on side surface quality, residual stress, microstructure, and mechanical property are still quite lacking. The influence of the repeated usage of LR on a solidified layer is also not very clear. To address these issues, LR treatments with the cyclic numbers of 1-3 on every solidified layer have been employed during the SLM processes of a Ti-5Al-2.5Sn alloy in this study and their influences on deposition quality, residual stress, microstructure, and mechanical property were researched. The results first indicated that although the improvement in top surface quality and densification degree would be more and more notable with the increase of LR cycles, the side surface quality could not be improved through all the LR treatments. Then, it was shown by the hole-drilling tests on the surface centers of several 15 x 15 x 3 mm(3) thin-plate specimens that when 1 cycle of LR was conducted on every solidified layer, the principal residual stress at the hole bottom of the SLM sample could be far beyond that of the non-treated one. In contrast, when 2 or 3 cycles of LR were conducted, the measured principal residual stresses could be reduced to lower than that of the non-treated ones. It was also proved that unlike the non-treated sample which presented a martensite-dominated microstructure with a very weak texture, all the LR-treated samples exhibited two kinds of preferential orientations. Finally, tensile properties of the stress-relieved samples were tested and it was seen that under the combined influence of the densification and the microstructure factors, the elongations of the LR-treated samples became slightly higher than that of the non-treated one whereas the tensile strengths were nearly identical. In summary, this paper demonstrates that there is still limitation in using LR as an auxiliary process of the SLM production of titanium products. The possible increase in residual stress and the formation of strong textures should be particularly considered.

Effect of Laser Remelting on Microstructure, Residual Stress, and Mechanical Property of Selective Laser Melting-Processed Ti-6Al-4V Alloy

Effect of Overlapping Remelting on Microstructures and Mechanical Properties of Selective Laser‐Melted Ti‐6Al‐4V Alloy

Effect of laser rescanning on Ti6Al4V microstructure during selective laser melting

Reduction of residual stress in porous Ti6Al4V by in situ double scanning during laser additive manufacturing

Effect of Laser Remelting on Deposition Quality, Residual Stress, Microstructure, and Mechanical Property of Selective Laser Melting Processed Ti-5Al-2.5Sn Alloy

Effects of remelting on the surface morphology, microstructure and mechanical properties of AlSi10Mg alloy fabricated by selective laser melting

Role of laser remelting and heat treatment in mechanical and tribological properties of selective laser melted Ti6Al4V alloy

Processing Parameter Effects on Residual Stress and Mechanical Properties of Selective Laser Melted Ti6Al4V

Effect of laser remelting on printability, microstructure and mechanical performance of Al-Mg-Sc-Zr alloy produced by laser powder bed fusion

The effect of laser surface re-melting on the surface roughness and micro-hardness of selective laser melting (SLM) fabricated Ti-6Al-4V samples

The effect of a remelting treatment scanning strategy on the surface morphology, defect reduction mechanism, and mechanical properties of a selective laser-melted Al-based alloy

Experimental Characterization and Strengthening Mechanism of Process-Structure-property of Selective Laser Melted 316 L

Study of pore defect and mechanical properties in selective laser melted Ti6Al4V alloy based on X-ray computed tomography

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Effect of Heat Treatment on Microstructure and Mechanical Properties of Ti6Al4V Alloy Fabricated by Selective Laser Melting

Effects of laser power on the microstructural evolution of novel Ti–6Zr–5Fe alloy fabricated by selective laser melting

Ti6Al4V Alloy Remelting by Modulation Laser: Deep Penetration, High Compactness and Metallurgical Bonding with Matrix

Role of processing parameters on relative density, microstructure and mechanical properties of selective laser melted titanium alloy

Study of residual stress in selective laser melting of Ti6Al4V

Investigation on influence of selective laser melting parameters on mechanical properties of Ti-6Al-4V alloy

The effect of selective laser melting process parameters and remelting scanning strategy on relative density and surface hardness of stainless steel 316L