Abstract:Titanium alloy is employed in aerospace, aviation, navigation, and other fields because of its excellent comprehensive properties, such as high specific strength, strong heat resistance, excellent corrosion resistance, and good low temperature performance. However the high cost of titanium alloy seriously restricts its large-scale application. Based on Ti-6Al-4V alloy which has the best comprehensive properties, several Ti-Al-V-Fe alloys with different contents of V and Fe were designed under the guideline of using cheap alloy elements instead of expensive alloy elements. With the help of the stability factor Kβ, the stability of β phase and the effect of β stabilizing elements were analyzed. The calculation models for critical cell coefficients ofβstabilizing elements of quenched alloys and annealed alloys were established by theoretical derivation. On this basis, the calculation methods for volume fraction of α phase and β phase were established, and the theoretical calculation of the volume fraction of α phase and β phase in Ti-Al-V-Fe alloy was realized. Taking Ti-6Al-3V-1Fe alloy as an example, the theoretical volume fraction of α phase and β phase in the alloy was calculated. Then, Ti-6Al-3V-1Fe alloy ingots were prepared by vacuum non-consumable arc melting furnace. Samples were taken and heat treated. Finally, the volume fraction of α phase and β phase in the alloy was determined by X-ray diffraction. It was found that the measured results were in good agreement with the theoretical calculation results, indicating that the established model is feasible to predict the volume fraction of α phase and β phase.

A Novel and High-Strength Ti–Al–V–Fe Alloy Prepared by Spark Plasma Sintering

Effects of Sintering Temperature and Holding Time on Microstructure and Mechanical Properties of Ti−1Al−8V−5Fe Prepared by Spark Plasma Sintering

A TiAl Based Alloy with Excellent Mechanical Performance Prepared by Gas Atomization and Spark Plasma Sintering

Preparation of fine-grains TiAl alloys by mechanical alloying and spark plasma sintering

Microstructures and Mechanical Properties of Ti-43Al-5V-4Nb-Y Alloy Consolidated by Spark Plasma Sintering

Microstructure and Mechanical Properties of a High-Strength Ti-4Al-2Fe-3Cu Alloy Fabricated by Sintering and Hot Extrusion

Cost-affordable, biomedical Ti-5Fe alloy developed using elemental powders and laser in-situ alloying additive manufacturing

Behaviour of novel low-cost blended elemental Ti-5Fe-xAl alloys fabricated via powder metallurgy

A beta-solidifying TiAl alloy reinforced with ultra-fine Y-rich precipitates

Microstructure, Densification and Mechanical Properties of Ti-22Al-25Nb Alloy Fabricated by Spark Plasma Sintering

Synthesis and Properties of an Ultrafine Grained Ti-45al-2cr-2nb-1b-0.5ta Alloy Prepared by Double Mechanical Milling and Spark Plasma Sintering

Microstructure and mechanical properties of Ti-43Al-9V alloy fabricated by spark plasma sintering

Preparation of Low-Cost Titanium Alloys Using Fe Instead of V:Calculation of Phase Volume Fraction

A new α + β Ti-alloy with refined microstructures and enhanced mechanical properties in the as-cast state

A titanium-nitrogen alloy with ultrahigh strength by ball milling and spark plasma sintering

Microstructural Evolution and Mechanical Properties of a High Yttrium Containing TiAl Based Alloy Densified by Spark Plasma Sintering

A β-solidifying TiAl alloy reinforced with ultra-fine Y-rich precipitates

Microstructures and Mechanical Properties of TiAl Alloy Prepared by Spark Plasma Sintering

Effect of Mechanical Alloying on Microstructure and Mechanical Properties of Ti-24Nb-4Zr-3Mn Alloys Prepared by Spark Plasma Sintering

Selective laser melting processing of heterostructured Ti6Al4V/FeCoNiCrMo alloy with superior strength and ductility

Fabrication and characterization of Ti-33Nb-4Sn alloys by cryomilling and spark plasma sintering