Abstract:This article presents a novel and feasible approach for researching the quantity of the ceramic phase and component optimization in high-temperature titanium alloys with small trace amounts of ceramic phases. Different near-α titanium alloys with varying yttrium and boron contents were prepared through the utilization of a vacuum non-consumable arc furnace melting method. The alloy used was a Ti-5.9Al-4Sn-3.9Zr-3.8Mo-0.4Si base. Its microstructure, texture, mechanical properties, and fracture behavior were studied. The observation of the as-cast structure shows that the addition of different doses of trace Y and B elements significantly refines both the original β grains and α grains. Moreover, the addition of the B element transforms the Widmanstätten structure in the titanium alloy structure into a basketweave structure. The addition of Y can refine the grain structure, improve the uniformity of the matrix structure, and act as a strong deoxidizer, which will take away the oxygen in the matrix and purify it. The TiB whiskers generated with the addition of B promotes dynamic recrystallization behavior and leads to more equiaxed α grains being precipitated around them, resulting in a significant refinement of the microstructure of the as-cast alloy. After adding a small amount of B, the texture strength of the α phase is significantly reduced, indicating that TiB whiskers inhibit the formation of texture. After conducting performance screening and structure analysis, the study supplements the analysis of Y’s regulation of the titanium alloy structure. The regulation is primarily explained by combining the results of the analysis of boron content, phase diagram analysis, mechanical properties, and fracture analysis. The mechanical analysis introduces the unique load transfer strengthening of TiB whiskers combined with an analysis of high-temperature mechanical properties, as the threshold for addition. The optimal amounts of Y and B additions are 0.6 wt% and 0.8 wt%, respectively. The optimized alloy obtained under this condition can achieve a tensile strength of 950 Mpa at 500 °C without any plastic deformation or heat treatment.

A β-solidifying TiAl alloy reinforced with ultra-fine Y-rich precipitates

Thermal stability and its effects on the mechanical properties of rapidly solidified Al-Ti alloys

Nano-yttrium-containing precipitates of T6 heat-treated A356.2 alloy when trace yttrium (Y less than 0.100 wt%) added

Refining Ti 2 AlC in the liquid region and improving the microstructure and mechanical properties of Ti-46Al-8Nb-2.6 C alloy by adding Y

Microstructure characterization and tensile performance of a high-strength titanium alloy with in-situ precipitates of Ti5Si3

In-situ synthesized a dual-scale Ti 2 AlC reinforced TiAl composites with superior mechanical properties

Improving mechanical property of Ti55531 alloy by yttrium dopant

Effect of Y Content on Precipitation Behavior, Oxidation and Mechanical Properties of As-Cast High-Temperature Titanium Alloys

Improving mechanisms of lamellar microstructure and mechanical properties by Y and in-situ Y2O3: Modification of carbides particles and complete transformation of Ti2AlC particles

Effects of yttrium additions on microstructures and mechanical properties of cast Al-Cu-Mg-Ag alloys

High-strength and thermally stable TiB2-modified Al–Mn–Mg–Er–Zr alloy fabricated via selective laser melting

Fabrication, microstructure and mechanical properties of TiAl matrix composite reinforced by submicro/nano-Ti 2 AlC

Microstructures Of Components Synthesized Via Electron Beam Selective Melting Using Blended Pre-Alloyed Powders Of Ti6al4v And Ti45al7nb

Investigation on the Optimal Amount of Y and B Elements in High-Temperature Titanium Alloy Ti-5.9Al-4Sn-3.9Zr-3.8Mo-0.4Si-xY-yB

Tailoring microstructure and mechanical performance of a β-solidifying TiAl alloy via martensitic transformation

Microstructures and mechanical properties during sinter-forging of a novel TiAl alloy

Sustaining an excellent strength-ductility combination of a PM α + β titanium alloy with fine prior β grains and heterogeneous microstructure

Microstructure and mechanical properties of Ta–Ti alloy by plasma-activated sintering

Microstructure, solidification behavior and mechanical properties of Al-Si-Mg-Ti/TiC fabricated by selective laser melting

The Crystal Structure, Microhardness and Thermal Stability of the Ti26Al55Zn19 Alloy

Microstructure Transformation of a Refined High Nb Containing TiAl Alloy