Abstract:As power efficiency becomes essential in automotive applications, DC-DC converters are widely employed [1]. However, size and thermal limits have made it challenging to continue using standard CMOS-based converters. Gallium Nitride (GaN) FETs, on the other hand, have a much higher conductivity with small size/capacitance in comparison to silicon FETs, enabling a highly efficient power conversion at high switching frequency (f SW ). However, there are several issues that must be resolved before using GaN in automotive. High f SW incurs larger di/dt and dv/dt transitions which injects high frequency electromagnetic interference (EMI) noise into the input bus. This creates unwanted noise or even a malfunction in a safety-critical system. A bulky input filter can reduce EMI, but it greatly increases size and cost. Several techniques [2-5] are reported to mitigate EMI. Frequency hopping using discrete frequencies is proposed in [2], but cannot spread the frequency evenly to lower the peak noise effectively. Alternatively, a series resistor is typically added at the gate of the GaN FET to slow down the transition [3-4]. However, the switching loss is dramatically increased. To mitigate this, adjustable driving strength is proposed in [5]. Unfortunately, the sensing and driver delays confine its use in low f SW applications, where the switch node rising time is several tens or hundreds of ns. Another issue of high f SW operation is that it causes significant current and voltage spikes due to the parasitics at the drain/source of the high side GaN FET (M H ), which could lead to GaN VDS breakdown or damage on logic-level FETs. Thus, EMI noise suppression and reliable operation of GaN FETs remain as major challenges in realizing high f SW power converters for automotive-use.

Performance Evaluation of 40-V/10-A GaN HEMT Versus Si MOSFET for Low-Voltage Buck Converter Application

A 2–10 MHz GaN HEMTs Half-Bridge Driver with Bandgap Reference Comparator Clamping and Dual Level Shifters for Automotive Applications

A Tri-Slope Gate Driving GaN DC–DC Converter with Spurious Noise Compression and Ringing Suppression for Automotive Applications

25.2 A 10mhz 3-to-40v VIN Tri-Slope Gate Driving GaN DC-DC Converter with 40.5dbµv Spurious Noise Compression and 79.3% Ringing Suppression for Automotive Applications

A Buck Converter with Cost-Effective GaN/Si Hybrid Switches and CRM Operation for High-Efficiency and High-Power-Density Applications

A Comparative Study on the Switching Performance of GaN and Si Power Devices for Bipolar Complementary Modulated Converter Legs

Performance Analysis of a Single-phase GaN-based 3L-ANPC Inverter for Photovoltaic Applications

Reliability-Driven Assessment of GaN HEMTs and Si IGBTs in 3L-ANPC PV Inverters

Comparison of the performance of Si, SiC, and GaN based switching elements in high gain DC-DC boost converter

Cryogenic Overcurrent Characteristic of GaN HEMT and Converter Evaluation

Review of GaN HEMT Applications in Power Converters over 500 W

Evaluating Switching Performance of GaN HEMT Using Analytical Modeling

A New GaN-Based Device, P-Cascode GaN HEMT, and Its Synchronous Buck Converter Circuit Realization

A Postprocessing-Technique-Based Switching Loss Estimation Method for GaN Devices

A Comparative Study of GaN HEMT and Si MOSFET-Based Active Clamp Forward Converters

Accurate Evaluation of Commutations of 650 V GaN Power Switches Assisted by Electromagnetic Simulations in a 7 kW Dual Active Bridge Converter for Automotive Battery Charging Applications

Analysis of MHz 380V-12V DCX with Low FoM Device

A 3kw GaN HEMT Based Three-phase Converter Achieving a Switching Frequency of 300khz and an Efficiency of 97.06%

Analysis of Dead-time Related Loss on GaN-based Synchronous Buck Converter

Loss Analysis of GaN Devices in an Isolated Bidirectional DC-DC Converter

Comparisons on Different Innovative Cascode GaN HEMT E-Mode Power Modules and Their Efficiencies on the Flyback Converter