Abstract:We investigated the effect of mixing protocol on the morphology of compatibilized polymer blends made with premade compatibilizer and reactively formed in-situ compatibilizer in a custom-built miniature mixer Alberta Polymer Asymmetric Minimixer (APAM). The compatibilized blends show a finer morphology than uncompatibilized blends if the polymers are mixed together in the dry state and then fed into the mixer. It is found that premelting one polymer, and premixing polymers and compatibilizer, both greatly affect the compatibilized blends' morphology. The effects are complex since the dispersed phase particle size and distribution of the compatibilized blends may be smaller or larger when compared with the uncompatibilized system, depending on the material's physical and chemical properties; for example, diblock molecular weight or the preference of copolymer to migrate to a particular phase can change the final morphology. Good mobility of the copolymer to reach the interface is crucial to obtain a finer morphology. Micelles are observed when a high molecular weight diblock copolymer P(S-b-MMA) is used for a PS/PMMA blend. Because of its enhanced mobility, no micelles are found for a low molecular weight diblock copolymer P(S-b-MMA) in a PS/PMMA blend. For PS/PE/P(Sb-E) blends, finer morphology is obtained when P(S-b-E) is first precompounded with PS. Because the block copolymer prefers the PE phase, if the P(S-b-E) block copolymer is compounded with PE first, some remains inside the PE phase and does not compatibilize the interface. In the case of reactive blend PSOX/PEMA, premelting and holding the polymers at high temperature for 5 min decreases final dispersed phase particle size; however, premelting and holding for 10 min coarsens the morphology.

EFFECTS OF COMPATIBILIZER SB ON THE DISPERSED PHASE SIZES OF LDPE／PS BLENDS

Compatibilizing Efficiency of Copolymer Precursors for Immiscible Polymer Blends

A Dissipative Particle Dynamics Study on the Compatibilizing Process of Immiscible Polymer Blends with Graft Copolymers

Effect of Mixing Protocol on Compatibilized Polymer Blend Morphology

Compatibilization of LDPE/PS blends with block copolymers. Effect of the order of mixing on the LDPE/SEBS/PS blend morphology

Effects Of Styrene-Ethylene/Propylene Diblock Copolymer (Sep) On The Compatibilization Of Pp/Ps Blends

Polystyrene/High Density Polyethylene Blends Compatibilized by a Tri-Block Copolymer I. Properties and Morphology

Solvent-Induced Morphology of the Binary Mixture of Diblock Copolymer in Thin Film: the Block Length and Composition Dependence of Morphology

Effects of SEP on The Compatibilization of PP/PS Blends

Molecular Simulation of Miscibility of Poly(2,6‐dimethyl‐1,4‐phenylene Ether)/poly(styrene‐co‐acrylonitrile) Blend with the Compatibilizer Triblock Terpolymer SBM

Effect of Compatibilizer Content on the Tensile Properties and Fracture Toughness of High Density Polyethylene/Polystyrene Blends

Influences of Compatibilization and Compounding Process on Electrical Conduction and Thermal Stabilities of Carbon Black‐filled Immiscible Polypropylene/polystyrene Blends

Effect And Mechanism In Compatibilization Of Poly(Styrene-B-2-Ethyl-2-Oxazoline) Diblock Copolymer In Poly(2,6-Dimethyl-1,4-Phenylene Oxide) Poly(Ethylene-Ran-Acrylic Acid) Blends

Morphology Evolution in PC/PE Blends with and without Compatibilization During Twin-Screw Extrusion

Effects of solubility parameter difference and molecular weight ratio on the dispersed phase size

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends

Dual Effects of Compatibilizer on the Formation of Oriented Ribbon-Like Dispersed Phase Domains in Polystyrene/polyamide 6 Blends

THE COMPATIBILITY OF SYNDIOTACTIC POLYSTYRENE/ISOTACTIC POLYPROPYLENE/SYNDIOTACTIC POLYSTYRENE-b-POLY(1-BUTENE) BLENDS

Influence of processing conditions on mechanical properties of blends of styrenic block copolymer and poly(phenylene oxide): Miscibility and microdomain size

Studies On High Density Polyethylene/Polycarbonate Blend System Compatibilized With Low Density Polyethylene Grafted Diallyl Bisphenol A Ether

STUDY ON THE NYLON 6/POLYSTYRENE BLENDS WITH THE STYRENE-b-ETHYLENE OXIDE DIBLOCK COPOLYMER AS COMPATIBILIZER