Abstract:This study aims to examine the 50/50 polypropylene/polyamide 6 (iPP/PA6) system molded under confined flow conditions, both in its original state and after being modified by two different interfacial agents. This study provides two main insights. Firstly, it focuses on a polymer blend close to phase inversion. Secondly, it investigates the impact of using two different types of interfacial agents (derived from polymer waste) to enhance the compatibility between iPP and PA6. Dynamic Mechanical Analysis (DMA) has been employed to achieve these objectives. It is important to note that the investigation of the 50/50 iPP/PA6 system is a crucial focus predicted in previous studies, where a series of mechanical properties were evaluated using Box–Wilson design of experiments (DOEs) over the whole compositional range on the iPP/PA6 binary system. Thus, two interfacial modifiers, namely succinic anhydride (SA)-grafted atactic polypropylene with terminal, side, and bridge SA grafts (aPP-SASA) and succinyl-fluoresceine (SF) with bridge succinic anhydride grafting atactic polypropylene (aPP-SFSA), were employed. The authors obtained and characterized these agents. The quantity of these agents used in the blend was identified as a critical coordinate in prior studies conducted by the authors. The processing method used, compression molding under confined conditions, was chosen to minimize any orientation effect on the emerging morphology. All characterization procedures were performed on samples processed by contour machining to retain the blend morphologies as they emerged from the processing stage. Results from WAXS and SAXS synchrotron tests concluded there were no changes in the crystal morphology of the iPP or the PA6 in the blends nor any co-crystallization process throughout the compositional range. These findings, and the long period fits on the PP crystalline phase for the fifty/fifty blends we are discussing, will support the present DMA study. Finally, the efficiency of these interfacial modifiers has been concluded, even in this unfavorable scenario.

THE COMPATIBILITY OF SYNDIOTACTIC POLYSTYRENE/ISOTACTIC POLYPROPYLENE/SYNDIOTACTIC POLYSTYRENE-b-POLY(1-BUTENE) BLENDS

Compatibilizing Efficiency of Copolymer Precursors for Immiscible Polymer Blends

The Morphology and Mechanical Properties of Sps/ipp Blends

Thermal behaviors of syndiopolystyrene/isotactic polypropylene blends

Influences of Compatibilization and Compounding Process on Electrical Conduction and Thermal Stabilities of Carbon Black‐filled Immiscible Polypropylene/polystyrene Blends

PRELIMINARY INVESTIGATION ON THE MISCIBILITY OF ISOTACTIC POLYPROPYLENE （ipp） AND SYNDIOTACTIC POLYPROPYLENE （spp） BLENDS

Blends of Syndiotactic Polystyrene and Isotactic Polypropene Prepared Using a Ziegler‐Natta Catalyst Containing a Novel Donor

Preparation and Characterization of Poly(butylene Succinate-Co-adipate)/poly(lactic Acid) Blends with Enhanced Compatibility, Mechanical Properties, and Heat Resistance

Compatibility evaluation and mechanical properties of isotactic polypropylene/high density polyethylene (iPP/HDPE) blends

Rheology of Poly(lactic Acid)/poly(trimethylene Terephthalate) Blends Compatibilized by Clay or Maleic Anhydride-Grafted Poly(ethylene-Octene) Elastomer

Preparation of Polypropylene and Polystyrene with NCO and NH2 Functional Groups and Their Applications in Polypropylene/polystyrene Blends

Compatibilization And Toughening Of Immiscible Ternary Blends Of Polyamide 6, Polypropylene (Or A Propylene-Ethylene Copolymer), And Polystyrene

Morphology and Mechanical Behavior of Isotactic Polypropylene (ipp)/syndiotactic Polypropylene (spp) Blends and Fibers

Morphology, thermal behavior, rheological, and mechanical properties of polypropylene/polystyrene blends based on elongation flow

Compatibilization and morphology development of immiscible ternary polymer blends

Miscibility of isotactic polypropylene with random and block ethylene-octene copolymers studied by atomic force microscopy-infrared

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends

Correlation of Morphology Evolution with Superior Mechanical Properties in PA6/PS/PP/SEBS Blends Compatibilized by Multi-phase Compatibilizers

Crystallization Behavior of the Blends of Isotactic Polypropylene and Ethylene-Propylene Blocky Copolymers

A Dynamic Mechanical Analysis on the Compatibilization Effect of Two Different Polymer Waste-Based Compatibilizers in the Fifty/Fifty Polypropylene/Polyamide 6 Blend

Crystallization and phase behavior of crystalline syndiotactic 1,2-polybutadiene/isotactic polypropylene blends in solution-cast thin films