Abstract:In the recent decades, there has been an increasing interest in preparing novel polymeric blending materials with combined and additional characteristics of each component. Having a relatively high modulus, toughness and strength, low creep, and good temperature resistance, nylons have been widely applied in the automotive industry, machinery, electronic equipment, and military applications [1]. It is well-known that blends consisting of nylon and elastomer possess excellent toughness; however, due to its highly polar amide end-groups, nylon is incompatible with elastomer. In general, it is believed that functionalization of the elastomer is a preferred approach to enhance the interfacial properties between these polymers. Research concerning nylon/functionalized elastomer blends has mostly focused on the aspects of mechanical and thermal properties. To our knowledge, only a few reports have dealt with dynamic rheological behavior of their melts [2–4]. The rheological measurements not only give much useful information for material moulding and processing, but also is an important way to characterize the structure and properties of polymer materials [5, 6]. The aim of this article is to study the influence of the graft reaction between nylon1212 and SEBS-gMA on dynamic rheological behavior and morphology of their blends. Nylon1212 (melt-flow index = 22.43 g/min) used here was obtained from Shandong Dongchen Engineering Plastic Co., Ltd., China. The elastomer, a triblock copolymer styrene-b-(ethylene-co-butylene)-b-styrene (SEBS 4033) was supplied by the Yuyao Huiju Polymer Co., Ltd. China. The maleated triblock copolymer styrene-b-(ethylene-co-butylenes)-b-styrene (SEBS-gMA) was supplied by Yuyao Yongcheng Engineering plastics Co., Ltd., China. The grafting ratio of maleic anhydride is 1.84 wt%. Both SEBS and SEBSg-MA consist of 30 wt% polystyrene end-blocks. The nylon1212/SEBS blends and nylon1212/SEBS-g-MA blends including 1 wt% antioxidant (1010) were prepared in a corotating twin-screw extruder (PRISM TES 16TC, UK) at 210 ◦C. All the samples were compression-moulded into disks of 25 mm in diameter and 1.2 mm in thickness at 180 ◦C, 50 MPa. Melt rheological tests were conducted in an ARES Rheometer

The Effect of Blending Sequence on Phase Morphology of Nylon 6/abs/sma Blends

Synergetic Effect of a Reactive Compatibilizer and Organo-montmorillonite on the Dispersion of Polyamide 6 /Polydimethylsilicone Blend with a High Viscosity Ratio

MORPHOLOGY AND MECHANICAL PROPERTIES OF NYLON-6/ABS POLYMER BLENDS COMPATIBILIZED BY STYRENE-MALEIC ANHYDIDE COPOLYMER

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Morphology and Mechanical Properties of Nylon 6/PBT Blends Compatibilized with Styrene/Maleic Anhydride Copolymer

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends

Effect of blending sequence on the morphology and properties of polyamide 6/EPDM-g-MA/epoxy blends

Experimental Studies on the Phase Separation Behavior of Molten Benzenesulfonate-Modified PET/PA6 Blends

Study on the Structure and Properties of ABS/PA6/SMA Blends

Mechanical properties, rheology, and crystallization of epoxy-resin-compatibilized polyamide 6/polycarbonate blends: Effect of mixing sequences

Analysis of phase morphology and dynamics of immiscible PP/PA1010 blends and its partial-miscible blends during melt mixing from SEM patterns

Effect of nano-silica on the phase inversion behavior of immiscible PA6/ABS blends

Effect of poly(styrene-co-maleic anhydride) on physical properties and crystalline behavior of nylon-6/PEBA blends

Morphology Evolution of Miscible Blends Between Crystalline Pa6 and Amorphous Pa6icot

Rheological characterization and morphology of nylon 1212/functional elastomer blends

The dynamic rheological behavior and morphology of nylon/elastomer blends

Effect of Mixing Sequence on Phase Morphology and Mechanical Properties in Polyamide 6/butadiene (core) Styrene Acrylonitrile-G-Maleic Anhydride (shell) Latex/Organoclay Ternary Nanocomposites

Blends of rABS and SEBS: Influence of In-Situ Compatibilization on the Mechanical Properties

Effect of ABS types on the morphology and mechanical properties of PA6/ABS blends by in situ reactive extrusion

Creating Super-Tough and Strong PA6/ABS Blends Using Multi-Phase Compatibilizers

Suppression of Phase Coarsening in Immiscible, Co-Continuous Polymer Blends under High Temperature Quiescent Annealing