Abstract:Objectives: During the manufacturing of Porcelain Veneered Zirconia (PVZ) dental crowns, the veneer-core system undergoes high-temperature firing cycles and gets fused together which is then, under a controlled setting, cooled down to room temperature. During this cooling process, the mismatch in thermal properties between zirconia and porcelain leads to the development of transient and residual thermal stresses within the crown. These thermal stresses are inherent to the PVZ dental crown systems and render the crown structure weak, acting as a precursor to veneer chipping, fracture, and delamination. In this study, the introduction of an intermediate functionally graded material (FGM) layer at the bi-material interface is investigated as a potentially viable alternative for providing a smoother transition of properties between zirconia and porcelain in a PVZ crown system. Methods: Anatomically correct 3D crown models were developed for this study, with and without the FGM layer modeled at the bi-material interface. A viscoelastic finite element model was developed and validated for an anatomically correct bilayer PVZ crown system which was then used for predicting residual and transient stresses in the bilayer PVZ crown. Subsequently, the viscoelastic finite element model was further extended for the analysis of graded sublayers within the FGM layer, and this extended model was used for predicting the residual and transient stresses in the functionally graded PVZ crown, with an FGM layer at the bi-material interface. Results: The study showed that the introduction of an FGM layer at the bi-material interface has the potential to reduce the effects from transient and residual stresses within the PVZ crown system relative to a bilayer PVZ crown structure. Furthermore, the study revealed that the FGM layer causes stress redistribution to alleviate the stress concentration at the interfacial surface between porcelain and zirconia which can potentially enhance the durability of the PVZ crowns towards interfacial debonding or fracture. Significance: Thus, the use of an FGM layer at the bi-material interface shows a good prospect for enhancing the longevity of the PVZ dental crown restorations by alleviating the abrupt thermal property difference and relaxing thermal stresses.

Mechanical analysis and fabrication of the bioinspired functionally graded interface layer of all-ceramic restoration

Optimization design of bioinspired functionally graded interface layer of all ceramic restoration

Investigation of the structure and mechanical properties of a novel dental graded glass/zirconia ceramic

The optimization design of the bioinspired functionally graded interface layer of the three dimensional cambered all-ceramic restoration

The effect of graded glass-zirconia structure on the bond between core and veneer in layered zirconia restorations

Mechanical Performance of Polymer-Infiltrated Zirconia Ceramics.

Exploring the Optimal Pre-Sintering Temperature on Compressive Strength and Anti-Fatigue Property of Graded Zirconia-Based Glass/Zirconia Structure

Surface Modification of Dental Zirconia Implants with a Low Infiltration Temperature Glass

Microstructure and Nanoindentation Analyses of Low-Temperature Aging on the Zirconia-Porcelain Interface.

Fabrication and Characterization of Dental Restorative Composites with Gradient Properties

Biomechanical behavior of functionally graded S53P4 bioglass-zirconia dental implants: Experimental and finite element analyses

[Study of relationship between powder-size gradation and mechanical properties of Zirconia toughened glass infiltrated nanometer-ceramic composite powder]

Functionally graded bi-material interface for Porcelain Veneered Zirconia dental crowns: A study using viscoelastic finite element analysis

Preparation and Characterization of Functional Gradient Porous Zro2 Ceramics

[Influence on Mechanical Properties and Microstructure of Nano-Zirconia Toughened Alumina Ceramics with Nano-Zirconia Content].

High Strength and Toughness in Chromatic Polymer-Infiltrated Zirconia Ceramics.

In Vitro Cell Proliferation and Mechanical Behaviors Observed in Porous Zirconia Ceramics.

Optimizing the Design of Bio-Inspired Functionally Graded Material (FGM) Layer in All-Ceramic Dental Restorations.

On the Interfacial Fracture Resistance of Resin-Bonded Zirconia and Glass-Infiltrated Graded Zirconia

Digital light printing of zirconia/resin composite material with biomimetic graded design for dental application

Fracture mechanics analyses of ceramic/veneer interface under mixed-mode loading