Abstract:Objective: This study aims to analyse the influence of different lining material, thickness and coverage on residual stress of class II molar restoration by the multilayer technique through the three-dimensional (3D) finite element (FE) method. The objective is to reveal the correlations between the base layer configurations and the residual stress distributions of the tooth. Methods: A 3D reconstructed model of an extracted first molar was built through micro-CT images and a class II mesio-occlusal-distal cavity was prepared using computer-aided engineering (CAE) software. A bilayer technique was then applied, and 3D FE analyses were performed under polymerization contraction loading. Glass ionomer composites (Vitrebond and Ionosit) and flowable composite resin (Luxa Flow and Z350 Flowable Restorative) were used as lining materials. Moreover, several sensitivity analyses with dozens of hypothetical lining materials were conducted to provide definitive results. The thickness of the base layers was set to be distinct (0.5 mm or 1 mm) so as to reveal its effect on the stress alleviation. Various lining strategies with the liner covering different areas of the cavity walls (Closed Sandwich, Open Sandwich and Special Open Sandwich) were adopted to determine the effects of the base layers. Results: Adoption of an appropriate liner could effectively reduce the polymerization shrinkage stress. The mechanical properties of the base layer can affect the residual stresses, basically a lower Young's modulus and lower Poisson's ratio (of lining material) result in better stress mitigation, therefore reducing the stress transmitted to the dentin. Increase of the lining thickness within a certain range could lead to a decrease in the probability of stress concentration formation. Lining strategies had the strongest influence on the stress distributions. Different lining coverage could cause various stress responses, and covering all cavity walls with the lining material had the optimal performance among all the simulations in this study. Significance: The multilayer technique is an effective way to prolong the service life of resin composites restorations. A thorough evaluation of the sandwich technique through the FE method can provide a better understanding of the stress distributions of the restoration, and reveal its internal mechanisms.

Optimizing the Design of Bio-Inspired Functionally Graded Material (FGM) Layer in All-Ceramic Dental Restorations.

The optimization design of the bioinspired functionally graded interface layer of the three dimensional cambered all-ceramic restoration

Optimization design of bioinspired functionally graded interface layer of all ceramic restoration

A parametrical finite element analysis for functionally graded material overlay restoration

Functionally graded bi-material interface for Porcelain Veneered Zirconia dental crowns: A study using viscoelastic finite element analysis

Structural optimization and three-dimensional finite element analysis of functionally graded dental implants

Digital light printing of zirconia/resin composite material with biomimetic graded design for dental application

The effect of dental restoration geometry and material properties on biomechanical behaviour of a treated molar tooth: A 3D finite element analysis

Effects of the lining material, thickness and coverage on residual stress of class II molar restorations by multilayer technique

Mechanical analysis and fabrication of the bioinspired functionally graded interface layer of all-ceramic restoration

Influence of restorative material and cement on the stress distribution of endocrowns: 3D finite element analysis

To reduce the maximum stress and the stress shielding effect around a dental implant–bone interface using radial functionally graded biomaterials

Micromechanical modelling for bending behaviour of novel bioinspired alumina-based dental composites

Optimizing restorative procedure and material selection for pulpotomized primary molars: Mechanical characterization by 3D finite element analysis

[Three-Dimensional Finite Element Analysis on Half of the Structure Defect with Post Core and All-Ceramic Crown Restoration of Mandibular First Molar].

Influence of margin design and restorative material on the stress distribution of endocrowns: a 3D finite element analysis

Finite element analysis of residual stress in a bilayered all-ceramic crown

FEA Comparison of the Mechanical Behavior of Three Dental Crown Materials: Enamel, Ceramic, and Zirconia

Methodological approaches in graded dental ceramics

Functionalized Cortical Bone‐Inspired Composites Adapt to the Mechanical and Biological Properties of the Edentulous Area to Resist Fretting Wear

[Three-Dimensional Finite Element Analysis of Cuspal-Coverage Thickness Influence on the Stress Distribution of All-Ceramic Onlay-Restored Premolars].