Abstract:A wind turbine is a conversion mechanism that converts wind energy into electrical energy, but the conversion efficiency cannot reach 100%, so there is partial loss. These losses are converted into thermal energy, which in turn causes the wind turbine to heat up and affect generator performance. Therefore, the cooling and temperature field analysis of wind turbines is very important. In this paper, an electromagnetic analysis model is established by using the parameters of a 4 MW wind turbine; the losses of each part of the generator under rated load and three-phase short-circuit conditions are calculated, respectively; and the heat source is imported into the workbench fluent software to determine the cooling mode, so as to obtain the magnetic-thermal-flow field coupling model of permanent magnet synchronous direct drive wind turbine. The temperature distribution and temperature rise of the generator are obtained. Under the rated load condition, the overall maximum temperature rise of the wind turbine is 41.4 °C, about 180 mm near the fluid outlet side, which is as high as the winding temperature rises, because the winding is the main heating body. The maximum temperature rise of the rotor model and the permanent magnet model is about 36 °C. Under the three-phase short circuit condition, the temperature distribution of each component is similar to that under the rated load condition, and the temperature near the fluid inlet is low; the lowest is only 29.8 °C. The higher the temperature at the fluid's outlet, but not close to it, the higher the temperature is when it is about 180 mm away from the fluid's outlet side. The temperature difference in the same axial length is relatively large, with a maximum temperature difference of about 120 °C. The temperature distribution and temperature rise of the generator are independent of the operating conditions, which mainly affect the value. Additionally, through experimental verification, the minimum error under the rated load condition is 1.05%, the maximum error is 3.3%, and the average error is 2.30%. The minimum error under the three-phase short-circuit condition is 1.5%, the maximum error is 3.62%, and the average error is 2.26%. The difference with the engineering error range requirements is small, indicating the reasonable and effective effectiveness of this method. This study aims to provide a strong reference for analyzing the cooling and magnetic thermal flow field and a coupling analysis of direct drive wind turbines.

Transient thermal impact research on turbine rotors based on thermoelastic coupling

Numerical Investigation of the Impact of Wind Turbine Rotor on the Passive Cooler above Nacelle

Calculation of Finite Element of Thermal Stress and Analysis of Low-cyclic Fatigue Life for Non-central Hole Rotor of 135 MW Turbine

Transient Thermal Stress Analysis of Power Turbine Welded Rotor in a Heavy-Duty Gas Turbine During Rapid Load Changes

Study on dynamic thermal stresses in large-scale steam turbine rotors

Research on multi-disciplinary coupling mechanism between internal flow heat transfer and solid deformation in turbine

Thermal Growth Simulations Of The Rotor And Auxiliary Bearing Contact Events

Research on infrared nondestructive testing and thermal effect analysis of small wind turbine blades under natural excitation

Flow-thermo-elastic coupled vibration characteristics of aeroengine high pressure rotor at the typical start and stop conditions

An analytical study of rotor dynamics coupled with thermal effect for a continuous rotor shaft

The Influence Made by the Central Hole of Steam Turbine Rotor to Temperature and Stress Distribution of Rotor

Static and Dynamic Stress of the Combined Rotor with Curvic Couplings Considering the Rough Three-Dimensional Interface at Extreme Operating Conditions

Numerical and Experimental Investigation on Thermohydrodynamic Performance of Turbocharger Rotor-Bearing System

Calculation and Analysis for Transient Blade-Tip Radial Running Clearance of HPT

Dynamic Analysis of Turbocharger Rotor Bearing with an Integrated Three Dimensional Thermohydrodynamic Model

Influence Of The Aerodynamic Vibration Excitation On The Turbine Blade Vibration In A Vehicle Turbocharger

Coupled Heat Transfer Predictions of Thermal Environment for a Turbine Rotor

New Monitoring Model of Thermal Stresses on Steam Turbine Rotors

Thermal-Fluid-Solid Coupling Analysis on the Temperature and Thermal Stress Field of a Nickel-Base Superalloy Turbine Blade

Thermal modal analysis of hypersonic composite wing on transient aerodynamic heating

Research on Temperature Distribution of Large Permanent Magnet Synchronous Direct Drive Wind Turbine