Abstract:To investigate how laser peen texturing (LPT) parameters affect the patterns formed on the surface of E690 high-strength steel, and how these patterns subsequently influence tribological properties, the LPT process, including multiple shocks, was simulated by ABAQUS and verified by experiments. The residual stress and microstructure on the surface of micro-dimples after LPT were measured and observed by X-ray stress analyzer and transmission electron microscope. The tribological properties of specimens with different LPT density and depth were tested by reciprocating friction experiments, and the worn surfaces were observed using a scanning electron microscope. The experimentally obtained plastic deformation depths of the micro-dimples were − 8.82 μm, −18.31 μm, −28.72 μm and − 36.34 μm when the shock number was varied from 1 to 4. The simulation and experiment results were within 3.3 %, verifying the accuracy and reliability of the simulation. When the shock number was ≥ 2, the residual stress values in all directions at the test points within the micro-dimples tended to be consistent, and the full width at half maximum (FWHM) values gradually increased with increasing shock number. The TEM images and electron diffraction pattern of the specimen after three shocks showed that nanocrystals are formed on the bottom surface of the micro-dimple. In the friction experiments, the average friction coefficient first decreased and then increased with increasing LPT density. The average friction coefficient was the lowest when the LPT density was 20 %, for a constant micro-dimple depth. When the LPT density was 20 %, increasing the micro-dimple depth had little effect on the average friction coefficient, but the stability time of the specimens increased substantially. The wear surface of the untextured specimen showed deep and wide wear marks, and serious abrasive wear and adhesive wear occurred. Suggested LPT parameters for optimum wear resistance are an LPT density of 20% and shock number of 3.

Studies on Geometric Morphologies of Micro Dimples Fabricated by High Strain Rate Laser Shock Processing

Study of Negative Side Wall Surface Roughness by Picosecond Photonic Impact Microdeposition

Experimental study on laser peen texturing and tribological properties of E690 high-strength steel

Study of micro-dimples fabricated on alumina-based ceramics using micro-abrasive jet machining

Investigation on the deformation progress and residual stress of Ti-6Al-4V alloy during laser shock peening

Microstructural evolution and mechanical behaviors of Al-Cu-Li alloy processed by laser shock peening

Microstructure evolution and mechanical properties of a lamellar near-α titanium alloy treated by laser shock peening

Laser Shock Peening of Ti6Al4V Alloy with Combined Nanosecond and Femtosecond Laser Pulses

An experimental study on a rapid micro imprinting process

Formation mechanism of residual stress hole under different pulse durations and shock pressure distributions in Ti6Al4V alloy during laser peen texturing

Micro-dimple Surface Texture Picosecond Laser Processing and Tribological Properties

On the Microstructure, Residual Stress and Fatigue Performance of Laser Metal Deposited TC17 Alloy Subjected to Laser Shock Peening

Mechanisms and characterization of a novel hybrid laser-enhanced particle laden electrochemical fabrication process for high quality micro-dimples on germanium wafers

Micro-dimple textured surface produced by laser-induced particle impact test and improving tribological performance

Effects of Multiple Laser Shock Peening Impacts on Microstructure and Wear Performance of Wire-Based Laser Directed Energy Deposition 17-4PH Stainless Steel

Morphological Analysis of Laser Surface Texturing Effect on AISI 430 Stainless Steel

Microstructure evolution and electroplasticity in Ti64 subjected to electropulsing-assisted laser shock peening

Laser shock peening regulating aluminum alloy surface residual stresses for enhancing the mechanical properties: Roles of shock number and energy

High-performance integrated additive manufacturing with laser shock peening –induced microstructural evolution and improvement in mechanical properties of Ti6Al4V alloy components

Surface Texturing for Low Friction Mechanical Components

Laser shock processing of titanium alloys: a critical review on the microstructure evolution and enhanced engineering performance