Abstract:Ti2AlNb alloy is a new type of lightweight and heat-resistant structural material that has been an active research topic with multi-phases due to its improved mechanical properties. However, the phase response under severe plastic deformation (SPD) at high strain rates is unclear, which limits the understanding of its strengthening mechanism. Here, laser shock peening (LSP) was employed to investigate the microstructure response of alpha 2, O, and B2/beta phases in Ti2AlNb alloy. After LSP, the highest density dislocations were generated in the B2/beta phases, followed by the O phases, and the least dislocations were observed in the alpha 2 phases. In the B2/beta phases, only dislocation tangles (DTs) were observed. Dislocation lines (DLs) and DTs were mainly distributed in the O phases. As for the alpha 2 phases, DLs were generated while a small number of DTs were piled up at the grain boundaries. In addition, parallel dislocations (PDs) with a spacing of about 135 nm can be observed on the surface of the alpha 2 phases, and the dislocations interspersed between PDs were composed of screw dislocations with long segments. In addition to dislocation structures, stacking faults (SFs) were observed in both alpha 2 phases and O phases, and mechanical twins were formed in the O phases, which were generated to coordinate the SPD induced on the surface. These dislocation structures formed dislocation cells (DCs) and sub-grain boundaries which further developed into high-angle grain boundaries (HAGBs) together with mechanical twins, dividing the coarse grains and refining the microstructure. As the depth increased, the responses of the three kinds of phases decreased. The PDs in the alpha 2 phases have widened spacing and could not penetrate the grains. The mechanical twins were gradually reduced until no obvious twin structure could be observed. Finally, dislocations, grain size, microhardness, and residual stress presented a gradient distribution. The improved microhardness (maximum 470 HV) and compressive residual stress (maximum -600 MPa) which were consistent with the refined grains and highdensity dislocations gradually decreased to that of the base metal (BM).

Microstructure evolution and mechanical properties of a lamellar near-α titanium alloy treated by laser shock peening

Molecular dynamics simulation of microstructural evolution and mechanical behavior of titanium alloy subjected to laser shock peening

Microstructural evolution and mechanical behaviors of Al-Cu-Li alloy processed by laser shock peening

Effects of Laser Shock Peening on Microstructure and Properties of Ti–6Al–4V Titanium Alloy Fabricated via Selective Laser Melting

Microstructural response and surface mechanical properties of TC6 titanium alloy subjected to laser peening with different laser energy

Laser shock processing of titanium alloys: a critical review on the microstructure evolution and enhanced engineering performance

Laser shock peened Ti-6Al-4 V alloy: Experiments and modeling

Microstructure and High-Temperature Tribological Properties of Ti–6Al–4V Alloy Treated by Laser Shock Peening

Plastic deformation behavior of titanium alloy by warm laser shock peening: Microstructure evolution and mechanical properties

Gradient microstructure and foreign-object-damaged fatigue properties of Ti6Al4V titanium alloy processed by the laser shock peening and subsequent shot peening

Unveiling the origins of work-hardening enhancement and mechanical instability in laser shock peened titanium

Laser Shock Peening of Ti6Al4V Alloy with Combined Nanosecond and Femtosecond Laser Pulses

Gradient Microstructure Response in Different Phases of Ti2AlNb Alloy with Laser Shock Peening

Achieving high strength and ductility in selective laser melting Ti-6Al-4V alloy by laser shock peening

Effect of laser-shock peening on the structure and nano-mechanical behavior of a Ti-based metallic glass

Analysis of microstructure and high-temperature tensile properties of 2060 Al-Li alloy strengthened by laser shock peening

High-performance integrated additive manufacturing with laser shock peening –induced microstructural evolution and improvement in mechanical properties of Ti6Al4V alloy components

Mechanical properties and strengthening mechanisms of Ti-6Al-4V treated by electro-pulsing assisted laser shock peening

On the Microstructure, Residual Stress and Fatigue Performance of Laser Metal Deposited TC17 Alloy Subjected to Laser Shock Peening

Optimized Mechanical Properties of the Hot Forged Ti-6Al-4V Alloy by Regulating Multiscale Microstructure Via Laser Shock Peening

Studies on Laser Shock Peening on Nanomechanical and Mechano-Chemical Properties of Titanium Alloy (Ti6Al4V)