Abstract:To investigate how laser peen texturing (LPT) parameters affect the patterns formed on the surface of E690 high-strength steel, and how these patterns subsequently influence tribological properties, the LPT process, including multiple shocks, was simulated by ABAQUS and verified by experiments. The residual stress and microstructure on the surface of micro-dimples after LPT were measured and observed by X-ray stress analyzer and transmission electron microscope. The tribological properties of specimens with different LPT density and depth were tested by reciprocating friction experiments, and the worn surfaces were observed using a scanning electron microscope. The experimentally obtained plastic deformation depths of the micro-dimples were − 8.82 μm, −18.31 μm, −28.72 μm and − 36.34 μm when the shock number was varied from 1 to 4. The simulation and experiment results were within 3.3 %, verifying the accuracy and reliability of the simulation. When the shock number was ≥ 2, the residual stress values in all directions at the test points within the micro-dimples tended to be consistent, and the full width at half maximum (FWHM) values gradually increased with increasing shock number. The TEM images and electron diffraction pattern of the specimen after three shocks showed that nanocrystals are formed on the bottom surface of the micro-dimple. In the friction experiments, the average friction coefficient first decreased and then increased with increasing LPT density. The average friction coefficient was the lowest when the LPT density was 20 %, for a constant micro-dimple depth. When the LPT density was 20 %, increasing the micro-dimple depth had little effect on the average friction coefficient, but the stability time of the specimens increased substantially. The wear surface of the untextured specimen showed deep and wide wear marks, and serious abrasive wear and adhesive wear occurred. Suggested LPT parameters for optimum wear resistance are an LPT density of 20% and shock number of 3.

Micro-dimple textured surface produced by laser-induced particle impact test and improving tribological performance

Improving Tribological Performance of Mechanical Components by Laser Surface Texturing

Surface Texturing for Low Friction Mechanical Components

Manipulation Tribological Behavior of Ti6Al4V Alloy Via a Duplex Treatment of Double Glow Plasma Surface Molybdenizing-Laser Surface Texturing (LST)

Experimental study on laser peen texturing and tribological properties of E690 high-strength steel

Tribological Properties of Ti6Al4V Titanium Textured Surfaces Created by Laser: Effect of Dimple Density

Effects of Laser Surface Texturing and Lubrication on the Vibrational and Tribological Performance of Sliding Contact

Fabrication of TiN Coatings Deposited on Laser Shock Micro-Textured Substrates for Improving the Interface Adhesion Properties of Coatings

Improved tribological performance of AISI 316L stainless steel by a combined surface treatment: Surface texturing by selective laser melting and plasma nitriding

Combined Effect of a Laser Cladded Coating and Surface Texture on Tribological Performance Under Dry Sliding and Starved Lubrication

Effect of Micro-Dimple Texture on the Tribological Performance of Brass with Titanium Nitride (TiN) Coating under Oil-Lubricated Conditions

Improvement of Surface Mechanical and Tribological Characteristics of L-PBF Processed Commercially Pure Titanium through Ultrasonic Impact Treatment

Effect of Nanosecond Laser Texturization on Tribological Behavior of AISI 321 Stainless Steel

Research on Wear Resistance of AISI 9310 Steel with Micro-Laser Shock Peening

Micro-dimple Surface Texture Picosecond Laser Processing and Tribological Properties

Correlation between surface textural parameter and tribological behaviour of four metal materials with laser surface texturing (LST)

Analysis of synergistic friction reduction effect on micro-textured cemented carbide surface by laser processing

Experimental Study on the Effect of Micro-Texture on EHL Point-Contact Film Thickness Subject to Sliding Conditions

Simulation of Residual Stress and Micro-plastic Deformation Induced by Laser Shock Imprinting on TC4 Titanium Alloy Aero-engine Blade

Effect of Micro-Dimple Geometry on the Tribological Characteristics of Textured Surfaces

Fabrication and droplet impact performance of superhydrophobic Ti6Al4V surface by laser induced plasma micro-machining