Session 32 Overview - Frequency Synthesizers Rf Subcommittee.

Wei Deng,Jaehyouk Choi,Wanghua Wu

DOI: https://doi.org/10.1109/ISSCC42613.2021.9366059

2021-01-01

Abstract:This session presents the latest advances in digital and analog phase-locked loops (PLLs) and FMCW chirp generators from 2.4 to 60GHz for high-performance wireless applications.

What problem does this paper attempt to address?

A Low-Phase-Noise UHF-Band Fractional-N Frequency Synthesizer

Rongqian Tian,Haoming Li,Jiarui Liu,Xiaofeng Wang,Zhiyu Wang,Xiaopeng Yu

DOI: https://doi.org/10.13290/j.cnki.bdtjs.2018.01.003

2018-01-01

Abstract:An ultrahigh frequency (UHF) band fractional-N frequency synthesizer with phase noise optimization technique was proposed and implemented,with an operating frequency of 0.8-1.6 GHz.The dead-zone elimination technique was adopted to reduce the noise influence induced by the phase frequency detector and charge pump on the system.The distributed varactor structure and second-order harmonic filtering technique were adopted in the voltage-controlled oscillator to achieve lower phase noise.The new type of notch filtering technique was adopted in the △-∑ modulator to further mitigate the inband phase noise and system spurs.The synthesizer was fabricated and verified in TSMC 180 nm CMOS process.The test results show that the proposed synthesizer achieves a maximum phase noise of-95,-127 and-146 dBc/Hz at 0.01,1 and 10 MHz offset,with the spurious suppression less than-81 dBc and the power dissipation of only 20 mW.The chip area is 2.5 mm×1.1 mm.
A 0.8–4.2 GHz Monolithic All-Digital PLL Based Frequency Synthesizer for Wireless Communications

Zhao Yuanxin,Gao Yuanpei,Li Wei,Li Ning,Ren Junyan

DOI: https://doi.org/10.1088/1674-4926/36/1/015001

2015-01-01

Abstract:A 0.8-4.2 GHz monolithic all-digital PLL based frequency synthesizer for wireless communications is successfully realized by the 130 nm CMOS process. A series of novel methods are proposed in this paper. Two band DCOs with high frequency resolution are utilized to cover the frequency band of interest, which is as wide as 2.5 to 5 GHz. An overflow counter is proposed to prevent the "pulse-swallowing" phenomenon so as to significantly reduce the locking time. A NTW-clamp digital module is also proposed to prevent the overflow of the loop control word. A modified programmable divider is presented to prevent the failure operation at the boundary. The measurement results show that the output frequency range of this frequency synthesizer is 0.8-4.2 GHz. The locking time achieves a reduction of 84% at 2.68 GHz. The best in-band and out-band phase noise performances have reached -100 dBc/Hz, and -125 dBc/Hz respectively. The lowest reference spur is -58 dBc.
A 1.5–1.9GHz phase-locked loop (PLL) frequency synthesizer with AFC and Σ-Δ modulator for Sub-GHz wireless transceiver

zongming jin,xiaobao yu,siyang han,ying song,ziqiang wang,jia wen,baoyong chi

DOI: https://doi.org/10.1109/ICSICT.2014.7021202

2014-01-01

Abstract:A 1.5-1.9GHz phase-locked loop (PLL) frequency synthesizer with automatic frequency calibration (AFC) and third-order Σ-Δ modulator for Sub-GHz wireless transceiver is presented. A LC VCO ranging from 1.5GHz to 1.9GHze is integrated on this chip to meet multiple protocols. The voltage controlled oscillator is designed with modified digital controlled capacitor array to extend tuning range while minimizing the phase noise. An automatic frequency calibration (AFC) algorithm was implemented in this synthesizer to find the appropriate control word of the capacitor array. A 20-bit third-order Σ-Δ modulator is utilized to reduce out-of-band phase noise and to meet the frequency resolution of less than 30Hz as well as agile switching time.
Design of A 2.4-Ghz Integrated Frequency Synthesizer

Fei Wang,Jianyu Zhang,Xuan Wang,Jinmei Lai,Chengshou Sun

DOI: https://doi.org/10.1109/aspdac.2005.1466608

2005-01-01

Abstract:A 2.4-GHz integrated frequency synthesizer of PLL-based in 0.35-/spl mu/m RF process is presented. A fully integrated cross-coupled LC VCO of low phase noise is implemented. Prescaler accompanied with phase-switching is used to eliminate the glitch. The charge-pump having excellent current matching performance and wide output voltage range is achieved. The synthesizer has a frequency tuning range from 2.28 to 2.75 GHz. The simulation results show that it dissipates less than 66mW; settle time is less 100ms; the phase noise is -117dBc/Hz@600KHz.
A 2.4-Ghz ISM Band Delta-Sigma Fractional-N Frequency Synthesizer with Automatic Calibration Technique

Shiwei Cheng,Ke Zhang,Shengguo Cao,Xiaofang Zhou,Dian Zhou

DOI: https://doi.org/10.5555/1482003.1482005

2008-01-01

Abstract:In the paper, a programmable phase-locked loop (PLL) based ISM band fractional-N frequency synthesizer, commonly used in wireless communication system, is presented. The third order error-feedback Delta-Sigma modulator and high linearity offset phase frequency detector (PFD)/ Charge Pump (CP) are adopted to reduce close-in phase noise due to ΔΣ quantization noise folding. Automatic calibration technique is also introduced to select the optimal frequency sub-band of voltage controlled oscillator (VCO) automatically through process, voltage and temperature (PVT) variation. The Synthesizer is designed in UMC.18µm RF process and has a die size of 1.5mm*2.3mm. The measured phase noise is -112 dBc/Hz at 1 MHz offset.
A 21–48 GHz Subharmonic Injection-Locked Fractional-N Frequency Synthesizer for Multiband Point-to-Point Backhaul Communications

Alvin Li,Shiyuan Zheng,Jun Yin,Xun Luo,Howard C. Luong

DOI: https://doi.org/10.1109/JSSC.2014.2320952

2014-01-01

Abstract:This paper presents a mm-wave subharmonic injection-locked (SHIL) fractional-N frequency synthesizer for wireless multiband point-to-point backhaul communications. The SHIL synthesizer implements a low-phase-noise 4.5-6.1 GHz PLL and injects its output to a ÷3/÷4 dual-modulus divider followed by an ultra-wideband injection-locked frequency-multiplier (ILFM) chain to achieve excellent phase noise over an ultra-wide frequency tuning range. The proposed ILFM chain employs higher-order LC tanks to generate a rippled phase response around 0 ° over a wide frequency range to significantly enhance the locking range and to eliminate expensive mm-wave frequency calibration loops. Fabricated in a 65 nm CMOS process, the synthesizer prototype measures a continuous output frequency range from 20.6 to 48.2 GHz with frequency resolution of 220 kHz and output phase noise between -107.0 and -113.9 dBc/Hz at 1 MHz offset while consuming 148 mW and occupying 1850 × 1130 μm 2.
A Millimeter-Wave Frequency Synthesizer Architecture with High Agility and High Resolution Performance

Yuanwang Yang,Cai, Jingye,Lianfu Liu

2010-01-01

Abstract:In this paper, an approach of developing high agility and resolution millimeter-wave synthesizer architecture without using PLL (Phase Locked Loop) is proposed. Using the frequency multiplying of DDS output signal to provide the local oscillators instead of PLL in traditional three frequency conversions scheme, with good frequency configuration and optimal utilization of DDS (Direct Digital Synthesizer), and high-speed controlling of FPGA (Field Programming Gate Array), the synthesizer implemented with good spectrum purity has excellent performance of both high agility and resolution. The measurement results show that, the millimeter-wave local oscillator's bandwidth is 160 MHz and the minimum frequency step is 0.931 Hz, the maximum frequency switching time is less than 1 us, the spurious level is better than -60 dBc, the phase noise level is better than -90 dBc/Hz at 1 kHz.
Session 26 Overview: RF Power-Amplifier and Front-End Techniques

Hongtao Xu,Toshiya Mitomo,James Buckwalter

DOI: https://doi.org/10.1109/ISSCC42613.2021.9365937

2021-01-01

Abstract:RF PAs and front-end building blocks are critical for the output power, noise, power-efficiency, out-of-band rejection, and antenna impedance tuning of wireless transceivers. The first three papers in this session cover mm-wave PAs with efficiency enhancement techniques for 5G applications. The next paper presents a 28GHz reflection-coefficient sensor for mm-wave antenna-tuner applications. The session continues with two digital-PA papers in sub-6GHz frequency bands with back-off efficiency enhancement. The session concludes with an N-path filter exhibiting impedance transformation and passive voltage gain.
Phase-locked Frequency Synthesis and Modulation for Modern Wireless Transceivers

Woogeun Rhee

DOI: https://doi.org/10.1109/cicc.2015.7338438

2015-01-01

Abstract:Basic PLL system design aspects and key circuit design issues have been discussed. Fractional-N PLL plays a critical role in modern wireless transceivers. TDC is the bottleneck of DPLL and requires further researches. Innovative PLL architectures and circuit techniques are highly demanded.
IEEE ASSCC 2023/ Session 10/ Paper 10.5.

Ruichang Ma,Haikun Jia,Hongzhuo Liu,Wei Deng,Zhihua Wang,Baoyong Chi

DOI: https://doi.org/10.1109/A-SSCC58667.2023.10347958

2023-01-01

Abstract:PLL frequency synthesizers with low jitter are essential for mm-Wave high-speed wireless communication systems and data converters. By doing away with the frequency doubler, low jitter synthesizers with the 2 ND harmonic output can simplify their architecture. Additionally, to produce high-quality local oscillator signals for 2ND harmonic output, it is beneficial to suppress the fundamental frequency component at 2 ND harmonic output. In general, lowering the voltagecontrolled oscillator's phase noise (PN) and reducing the PLL's bandwidth to suppress in-band noise are the two most popular ways to minimize PN of PLL. The phase noise of N-core VCO reduce PN by 10logN, which is an effective method for obtaining low PN. Additionally, increasing the reference clock frequency hence decreasing the loop frequency division ratio can decrease PN. Literature [1] used a reference clock frequency of 500MHz with 175mW to implement the PLL of 52-fs <inf xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">rms</inf> Jitter. Ref. [2] adopted a folded transformer-based series resonance CMOS VCO, the PN of which achieved -130.8dBc/Hz@1MHz, consumed 242mW while reducing the core area. Ref. [3] uses a clock frequency of 250MHz to reduce the overall contribution of VCO through wideband PLL, while suppressing the noise introduced by the reference clock through the design of double-sampling phase detector (SPD). Ref. [4] uses the high gain of phase-frequency detector (PFD) with time amplification to suppress the gain of CP, thus achieving the performance of 60-fs <inf xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">rms</inf> Jitter. This study presents the construction of a PLL based on a 4-core resistance-synchronized VCO that achieves 47-fs <inf xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">rms</inf> Jitter and produces 2 ND harmonic with fundamental frequency suppression.
A 22.5–31.2-GHz Continuously Tuning Frequency Synthesizer With 8.7-GHz Chirp for FMCW Applications

Bowen Chen,Wei Luo,Fuyue Wang,Yue Lin,Na Yan,Hongtao Xu

DOI: https://doi.org/10.1109/lmwc.2020.3010089

IF: 3

2020-09-01

IEEE Microwave and Wireless Components Letters

Abstract:This letter presents a fractional-N frequency synthesizer with an ultrawideband continuously tuning range of 32.4% centered at 26.85- and 8.7-GHz chirp for frequency-modulated continuous-wave (FMCW) radars. The synthesizer uses a fractional-N 9-GHz charge-pump phase-locked loop (CPPLL) cascaded by an injection-locked frequency tripler (ILFT). A voltage-controlled oscillator (VCO) with transformer (TFM) coupling for an enhanced linear control voltage range, a better quality factor and good isolation from the load seen by the resonator, and a wide output voltage range charge-pump (CP) are used to achieve the ultrawideband CPPLL. The ILFT is implemented using a weakly coupled TFM for broadband locking range and 3-dB output power. The synthesizer is fabricated in the 40-nm CMOS technology and consumes 28.5 mW. The phase noise (PN) of the synthesizer at 27 GHz is −97.87 dBc/Hz at 1 MHz and the prototype is capable of generating a triangle or sawtooth chirp of 8.7-GHz modulation bandwidth with an rms FM error of 0.04% of BWchirp.

engineering, electrical & electronic
A 3 to 5 Ghz Low-Phase-Noise Fractional-N Frequency Synthesizer with Adaptive Frequency Calibration for Gsm/Pcs/Dcs/Wcdma Transceivers

Pan Yaohua,Mei Niansong,Chen Hu,Huang Yumei,Hong Zhiliang

DOI: https://doi.org/10.1088/1674-4926/33/1/015001

2012-01-01

Journal of Semiconductors

Abstract:low-phase-noise Sigma-Delta fractional-N frequency synthesizer for GSM/PCS/DCS/WCDMA transceivers is presented. The voltage controlled oscillator is designed with a modified digital controlled capacitor array to extend the tuning range and minimize phase noise. A high-resolution adaptive frequency calibration technique is introduced to automatically choose frequency bands and increase phase-noise immunity. A prototype is implemented in 0.13 mu m CMOS technology. The experimental results show that the designed 1.2 V wideband frequency synthesizer is locked from 3.05 to 5.17 GHz within 30 mu s, which covers all five required frequency bands. The measured in-band phase noise are -89, -95.5 and -101 dBc/Hz for 3.8 GHz, 2 GHz and 948 MHz carriers, respectively, and accordingly the out-of-band phase noise are -121, -123 and -132 dBc/Hz at 1 MHz offset, which meet the phase-noise-mask requirements of the above-mentioned standards.
A Fully-Differential Phase-Locked Loop Frequency Synthesizer for 60-Ghz Wireless Communication

Kuang Lixue,Chi Baoyong,Chen Lei,Jia Wen,Wang Zhihua

DOI: https://doi.org/10.1088/1674-4926/35/12/125002

2014-01-01

Journal of Semiconductors

Abstract:A 40-GHz phase-locked loop (PLL) frequency synthesizer for 60-GHz wireless communication applications is presented. The electrical characteristics of the passive components in the VCO and LO buffers are accurately extracted with an electromagnetic simulator HFSS. A differential tuning technique is utilized in the voltage controlled oscillator (VCO) to achieve higher common-mode noise rejection and better phase noise performance. The VCO and the divider chain are powered by a 1.0 V supply while the phase- frequency detector (PFD) and the charge pump (CP) are powered by a 2.5 V supply to improve the linearity. The measurement results show that the total frequency locking range of the frequency synthesizer is from 37 to 41 GHz, and the phase noise from a 40 GHz carrier is -97.2 dBc/Hz at 1 MHz offset. Implemented in 65 nm CMOS, the synthesizer consumes a DC power of 62 mW, including all the buffers.
A Frequency Synthesizer With Optimally Coupled QVCO and Harmonic-Rejection SSBmixer for Multi-Standard Wireless Receiver.

Deping Huang,Wei Li,Jin Zhou,Ning Li,Jinghong Chen

DOI: https://doi.org/10.1109/JSSC.2011.2124970

IF: 5.4

2011-01-01

IEEE Journal of Solid-State Circuits

Abstract:This paper presents a wide-band fractional-N frequency synthesizer for multi-standard cellular and short-range wireless communication receivers. The synthesizer covers the frequency band from 1.8 to 6 GHz and supports the standards of DCS1800, WCDMA, TD-SCDMA, WLAN802.11 a/b/g and Bluetooth. Architecture design and frequency planning are carefully performed to tradeoff wide frequency range and pow...
Session 31 Overview - Analog Techniques Analog Subcommittee.

Marco Berkhout,Drew A. Hall,Jiawei Xu

DOI: https://doi.org/10.1109/ISSCC42613.2021.9365822

2021-01-01

Abstract:Analog techniques continue to push the frontiers of precision, power, and performance. This year’s edition features two amplifiers and two accurate, temperature insensitive frequency references. The first paper describes a closed-loop, filter-less Class-D headphone amplifier that achieves the best output efficiency with low-power operation. The second paper pushes the state-of-the-art with the highest energy efficiency and lowest area. The third paper describes another low-power, low-area frequency reference that requires only a single-point trim to cover the entire industrial temperature range. Lastly, the final paper achieves the lowest chopper-induced intermodulation distortion (IMD) of -125.9dB ever reported.
Session T1A: Tutorial: Phase-locked clock generation for SoC: Circuit and system design aspects

Woogeun Rhee

DOI: https://doi.org/10.1109/SOCC.2015.7406882

2015-01-01

Abstract:A phase-locked loop is a key building block in wireline and wireless systems. In the wireline systems, low-jitter clock generation and versatile clock-and-data recovery circuits are critical in high data rate I/O links. In the wireless systems, the DS PLL based synthesizer plays a critical role in modern transceivers not only as a local oscillator but also as a phase modulator with direct digital modulation. However, the traditional PLL in advanced CMOS technology suffers from poor scalability, loop parameter variability and leakage current problems. Accordingly, diversified PLL architectures and circuit techniques have been recently proposed in consideration of performance, power and cost, thus making it more difficult for circuit designers to choose the right design solution than ever. This tutorial gives some insight into PLL basics tailored for circuit designers. Then, system perspectives and practical circuit design aspects will be presented. Furthermore, various PLL architectures and design challenges will be discussed.
CMOS Implementation of an RF PLL Synthesizer for Use in RFID Systems

Xie Weifu,Li Yongming,Zhang Chun,Wang Zhihua

DOI: https://doi.org/10.3321/j.issn:0253-4177.2008.08.036

2008-01-01

Chinese Journal of Semiconductors

Abstract:An integrated RF PLL frequency synthesizer for use in RFID systems is presented.It integrates a voltage-controlled oscillator,phase frequency detector,charge pump,high-frequency dual-modulus divider,and digital programmable divider.The frequency synthesizer was implemented in a 0.18μm CMOS process.It uses a 13MHz crystal oscillator as input.The output range is from 860 to 960MHz,the phase margin is -123dBc/1MHz,the frequency step is 200kHz,and the change frequency is within 150μs.
An X～Ku Wide-Band Frequency Synthesizer with Fast Frequency Switching

YANG Yuan-wang,CAI Jing-ye,REN Wei,XU Rui-min

DOI: https://doi.org/10.3969/j.issn.1001-0548.2007.04.016

2007-01-01

Abstract:A novel method to develop a frequency synthesizer with wide frequency coverage, fast frequency switching speed, and low phase noise is proposed. With the proposed method, the high performance of low phase noise and fast frequency hopping speed is achieved by combining Phase Locked Loop (PLL) and mixer. The Phase and Frequency Detector (PFD) current of the PLL is applied to compensate the nonlinear property of Voltage Controlled Oscillator (VCO) and to avoid the degraded performance due to loop instability. By this, a 11.1～ 13.1 GHz frequency synthesizer with frequency-step 10 MHz and loop bandwidth 600 kHz is developed. Experimental results show that the performance of phase noise is better than ?83 dBc/Hz@1 kHz and its frequency hopping time is shorter than 10 μs.
A DDS-Driven ADPLL Chirp Synthesizer with Ramp-Interpolating Linearization for FMCW Radar Application in 65nm CMOS

Liheng Lou,Kai Tang,Zhongyuan Fang,Bo Chen,Ting Guo,Zhe Liu,Yuanjin Zheng

DOI: https://doi.org/10.1109/iscas.2018.8351363

2018-01-01

Abstract:The paper presents a wideband, low-power chirp synthesizer for Ku-band FMCW radars. The DDS-driven ADPLL chirp synthesizer generates chirps up to 2GHz bandwidth. A low-power DDS is employed to generate a stepped reference frequency for ADPLL to ensure the long term chirp linearity, while the ADPLL fulfill the ramp-interpolating linearization by generating a narrow band chirp within the step frequency. The entire chirp benefits from the phase domain modulation and mitigates ADPLL loop bandwidth variation to achieve high linearity and low power. A novel adaptive ramping control scheme is adopted to ensure the chirp rate is constant after combining the narrow band chirp segments. By this two-stage chirp generation, a 2-GHz chirp is achieved with low relative frequency RMS error. Fabricated in a 65nm CMOS, the synthesizer generates a wideband chirp from 13.9GHz to 15.9GHz with configurable rate from 0.25 to 4GHz/ms, and consumes 53.8mW.
Investigation of wideband synthesizer covering 16GHz to 32GHz

Ling Tian,Xiaowei Zhu,Yao Li,Ling Yang

DOI: https://doi.org/10.1109/UCMMT.2013.6641554

2013-01-01

Abstract:A wideband synthesizer is presented in this paper. The synthesizer is driven by DDS for fine frequency resolution. With multiplier module, the frequency band can be extended from 16GHz to 32GHz. The phase noise of 32 GHz is -93dBc/Hz (10kHz offset). The synthesizer is suitable for antenna measurement system.

Session 32 Overview - Frequency Synthesizers Rf Subcommittee.

A Low-Phase-Noise UHF-Band Fractional-N Frequency Synthesizer

A 0.8–4.2 GHz Monolithic All-Digital PLL Based Frequency Synthesizer for Wireless Communications

A 1.5–1.9GHz phase-locked loop (PLL) frequency synthesizer with AFC and Σ-Δ modulator for Sub-GHz wireless transceiver

Design of A 2.4-Ghz Integrated Frequency Synthesizer

A 2.4-Ghz ISM Band Delta-Sigma Fractional-N Frequency Synthesizer with Automatic Calibration Technique

A 21–48 GHz Subharmonic Injection-Locked Fractional-N Frequency Synthesizer for Multiband Point-to-Point Backhaul Communications

A Millimeter-Wave Frequency Synthesizer Architecture with High Agility and High Resolution Performance

Session 26 Overview: RF Power-Amplifier and Front-End Techniques

Phase-locked Frequency Synthesis and Modulation for Modern Wireless Transceivers

IEEE ASSCC 2023/ Session 10/ Paper 10.5.

A 22.5–31.2-GHz Continuously Tuning Frequency Synthesizer With 8.7-GHz Chirp for FMCW Applications

A 3 to 5 Ghz Low-Phase-Noise Fractional-N Frequency Synthesizer with Adaptive Frequency Calibration for Gsm/Pcs/Dcs/Wcdma Transceivers

A Fully-Differential Phase-Locked Loop Frequency Synthesizer for 60-Ghz Wireless Communication

A Frequency Synthesizer With Optimally Coupled QVCO and Harmonic-Rejection SSBmixer for Multi-Standard Wireless Receiver.

Session 31 Overview - Analog Techniques Analog Subcommittee.

Session T1A: Tutorial: Phase-locked clock generation for SoC: Circuit and system design aspects

CMOS Implementation of an RF PLL Synthesizer for Use in RFID Systems

An X～Ku Wide-Band Frequency Synthesizer with Fast Frequency Switching

A DDS-Driven ADPLL Chirp Synthesizer with Ramp-Interpolating Linearization for FMCW Radar Application in 65nm CMOS

Investigation of wideband synthesizer covering 16GHz to 32GHz