Phase-locked Frequency Synthesis and Modulation for Modern Wireless Transceivers

Woogeun Rhee

DOI: https://doi.org/10.1109/cicc.2015.7338438

2015-01-01

Abstract:Basic PLL system design aspects and key circuit design issues have been discussed. Fractional-N PLL plays a critical role in modern wireless transceivers. TDC is the bottleneck of DPLL and requires further researches. Innovative PLL architectures and circuit techniques are highly demanded.

What problem does this paper attempt to address?

A Fractional-N PLL for Multiband (0.8–6 GHz) Communications Using Binary-Weighted D/A Differentiator and Offset-Frequency Δ-Σ Modulator

Heng-Yu Jian,Zhiwei Xu,Yi-Cheng Wu,Mau-Chung Frank Chang

DOI: https://doi.org/10.1109/jssc.2010.2040232

IF: 5.4

2010-01-01

IEEE Journal of Solid-State Circuits

Abstract:A compact, low power and global-mismatch-tolerant 0.8-6 GHz fractional- N PLL is designed to cover IEEE 802.11abg, PCS/DCS and cellular bands. Two new techniques are proposed to cancel the in-band quantization noise and fractional spurs. Firstly, a second order binary-weighted digital/analog differentiator (DAD) is utilized to enable the second order mismatch shaping and reduce the quantization noise by 25 dB, along with advantages of compact circuit implementation with smaller routing area and less power consumption over those of dynamic element matching (DEM) based counterparts. Secondly, mechanisms causing fractional spurs are also identified and a third order offset-frequency delta-sigma (Δ-Σ) modulator is devised to decrease the in-band spurs by 20 dB in simulation and 8 dB in present single-ended circuit implementation.
A Low Power Sub-GHz PLL with Optimized LO Distribution Circuit

Lingchang Chen,Xiaopeng Yu,Hanqi Gao,Liying Cai,Kai Huang,Dandan Zheng

DOI: https://doi.org/10.1109/iws49314.2020.9360083

2020-01-01

Abstract:A wideband fractional-N phase-lock loop (PLL) is designed for sub-GHz wireless communications. The local oscillator (LO) distribution circuit is optimized with a low power consumption and high output amplitude to drive the mixer and power amplifier of the transceiver. Implemented with a commercial 0.13-μm CMOS process, the proposed PLL has a working range of 300MHz~1.26GHz with 3.5mW power consumption, including all the buffers from a 1.2V supply. It occupies a silicon area of 0.33mm 2 .
A Compact 0.8–6ghz Fractional-N PLL with Binary-Weighted D/A Differentiator and Offset-Frequency Δ−Σ Modulator for Noise and Spurs Cancellation

Heng-Yu Jian,Xu, Z.,Yi-Cheng Wu,Chang, Frank

2009-01-01

Abstract:A compact, low power and global-mismatch-tolerant 0.8-6GHz fractional-N PLL covers IEEE 802.11abg, PCS/DCS and cellular bands by using a binary-weighted 2nd order digital/analog differentiator (DAD) to achieve 2nd order mismatch shaping and reduce the quantization noise by 25dB, and using a 3rd order offset-frequency Δ-Σ modulator to reduce in-band spurs by 20dB in simulation and 8dB in current single-ended practice.
A Low Phase Noise, Wideband and Compact CMOS PLL for Use in a Heterodyne 802.15.3c Transceiver

David Murphy,Qun Jane Gu,Yi-Cheng Wu,Heng-Yu Jian,Zhiwei Xu,Adrian Tang,Frank Wang,Mau-Chung Frank Chang

DOI: https://doi.org/10.1109/jssc.2011.2143950

IF: 5.4

2011-01-01

IEEE Journal of Solid-State Circuits

Abstract:A low phase noise, wideband, mm-wave, integer-N PLL that is capable of supporting a 802.15.3c heterodyne TRX is reported. The PLL can generate 6 equally spaced tones from 43.2GHz to 51.84GHz, which is suitable for a heterodyne architecture with LO=(4/5)RF. Phase noise is measured directly at the LO frequency and is better than −97.5dBc/Hz@1MHz across the entire band. The total power consumption is 72mW from a 1V supply. The reported frequency synthesizer is smaller, exhibits less phase noise, and consumes less power than prior art. In addition, the LO tone corresponds to the fundamental of the VCO as opposed to a higher harmonic. Central to the PLL performance is the design of a low-noise, mm-wave VCO with a 22.9% tuning range. It is noted that resonator nonlinearities may result in significant up-conversion of flicker noise in wideband, mm-wave VCOs. To overcome this, Digitally-Controlled-Artificial-Dielectric (DiCAD) is used to linearize the resonator.
A Low Power Sub-GHz PLL with Optimized Class-C Voltage-controlled Oscillator

Junwen Zhang,Kewei Hu,Kaitian Huang,Kai Huang,Xiaopeng Yu

DOI: https://doi.org/10.1109/iws55252.2022.9977895

2022-01-01

Abstract:A wideband fractional-N phase-lock loop (PLL) is designed for sub-GHz wireless communications. Class-C voltage-controlled oscillator (VCO) circuit is optimized with low power consumption, followed by all-digital programmable counter to achieve flexibility in operating frequency. Implemented with a commercial 0.11-μm CMOS process, the proposed PLL has a working range of 680MHz - 998MHz with 2.69m W power consumption, including all the buffers from a 1.5V supply. It occupies a silicon area of 0.12mm 2 .
Multi-chip Phase Synchronization Circuit of Fractional-N PLL

Yantian Xu,Zhiyu Wang,Jiarui Liu,Hua Chen,Faxin Yu

DOI: https://doi.org/10.1587/elex.20.20230035

2023-01-01

IEICE Electronics Express

Abstract:A digital integrated circuit to realize multi-chip phase synchro-nization of fractional-N PLL with local oscillator divider is designed. An offset of fractional frequency ratio is added in phase difference calcula-tion, which effectively avoids the large calculation error under some special fractional frequency ratios. Different from traditional one-time synchro-nization, a synchronization method with tracking mode is proposed, which can further reduce the phase error. The test result of the chip finished in 65 nm COMS shows that the method of tracking mode and adding the fractional frequency ratio's offset are effective to reduce the error of phase synchronization to about 0.2 degrees.
Phase-Locked Frequency Generation and Clocking: Architectures and Circuits for Modern Wireless and Wireline Systems

Woogeun Rhee

2020-01-01

Abstract:Phase-Locked Frequency Generation and Clocking covers essential topics and issues in current Phase-Locked Loop design, from a light touch of fundamentals to practical design aspects. Both wireless and wireline systems are considered in the design of low noise frequency generation and clocking systems. Topics covered include architecture and design, digital-intensive Phase-Locked Loop s, low noise frequency generation and modulation, clock-and-data recovery, and advanced clocking and clock generation systems. The book not only discusses fundamental architectures, system design considerations, and key building blocks but also covers advanced design techniques and architectures in frequency generation and clocking systems. Readers can expect to gain insights into phase-locked clocking as well as system perspectives and circuit design aspects in modern Phase-Locked Loop design.
Fractional-N frequency synthesis: Overview and design perspectives

Woogeun Rhee,Bo Zhou,Zhihua Wang

DOI: https://doi.org/10.1109/RFIT.2011.6141757

2011-01-01

Abstract:This paper gives an overview of fractional-N frequency synthesis with design perspectives focusing on ΔΣ fractional-N phase-locked loops (PLLs). Spur generation and nonlinearity issue in the ΔΣ fractional-N PLLs are discussed with hardware results. High-order ΔΣ modulation with embedded FIR filtering is considered for low noise frequency generation. Also, various architectures of finite-modulo fractional-N PLLs are reviewed for alternative low noise design.
Session T1A: Tutorial: Phase-locked clock generation for SoC: Circuit and system design aspects

Woogeun Rhee

DOI: https://doi.org/10.1109/SOCC.2015.7406882

2015-01-01

Abstract:A phase-locked loop is a key building block in wireline and wireless systems. In the wireline systems, low-jitter clock generation and versatile clock-and-data recovery circuits are critical in high data rate I/O links. In the wireless systems, the DS PLL based synthesizer plays a critical role in modern transceivers not only as a local oscillator but also as a phase modulator with direct digital modulation. However, the traditional PLL in advanced CMOS technology suffers from poor scalability, loop parameter variability and leakage current problems. Accordingly, diversified PLL architectures and circuit techniques have been recently proposed in consideration of performance, power and cost, thus making it more difficult for circuit designers to choose the right design solution than ever. This tutorial gives some insight into PLL basics tailored for circuit designers. Then, system perspectives and practical circuit design aspects will be presented. Furthermore, various PLL architectures and design challenges will be discussed.
Fractional-N Frequency Synthesis: Overview and Practical Aspects with Fir-Embedded Design

Woogeun Rhee,Ni Xu,Bo Zhou,Zhihua Wang

DOI: https://doi.org/10.5573/jsts.2013.13.2.170

2013-01-01

Abstract:This paper gives an overview of fractional-N phase-locked loops (PLLs) with practical design perspectives focusing on a Delta Sigma modulation technique and a finite-impulse response (FIR) filtering method. Spur generation and nonlinearity issues in the Delta Sigma fractional-N PLLs are discussed with simulation and hardware results. High-order Delta Sigma modulation with FIR-embedded filtering is considered for low noise frequency generation. Also, various architectures of finite-modulo fractional-N PLLs are reviewed for alternative low cost design, and the FIR filtering technique is shown to be useful for spur reduction in the finite-modulo fractional-N PLL design.
14.1 A 0.048mm2 3mW synthesizable fractional-N PLL with a soft injection-locking technique

Wei Deng,Dongsheng Yang,Aravind Tharayil Narayanan,Kengo Nakata,Teerachot Siriburanon,Kenichi Okada,Akira Matsuzawa

DOI: https://doi.org/10.1109/ISSCC.2015.7063021

2015-01-01

Abstract:Phase-locked loops (PLLs) are a crucial building block in modern Systems-on-Chip (SoCs), which contain microprocessors, I/O interfaces, memories, power management, and communication systems. Fully synthesizable PLLs [1-2], designed using a pure digital design flow, have been proposed to reduce the design cost and allow easier integration. To achieve high-frequency resolution, PLLs are required to operate in fractional-N mode, in addition to integer-N mode. There are several architectures available [5-6] for realizing fractional-N operation. However, the existing topologies are not well suited for synthesis, as they require a time-to-digital converter (TDC) [3] and a digital-to-time converter (DTC) [4-5]. TDCs and DTCs are vulnerable to layout uncertainty, arising from automatic place and route (P&R), introducing linearity degradation and leading to poor in-band and out-of-band phase noise in PLLs. Injection locking is a promising technique for synthesizable PLLs. Unfortunately, it suffers from large spur caused by a periodic hard refresh, and limited fractional resolution, which is bounded to the inverse of the number of ring oscillator delay stages [6]. This paper describes a fully synthesizable fractional-N PLL with a soft injection-locking technique for smoothing switching and fine fractional resolution, and a cascading topology for suppressing the free-running oscillator phase noise over a wide loop bandwidth.
Design Techniques for CMOS Fractional-N Frequency Synthesizer

HUANG Shui-long,WANG Zhi-hua

DOI: https://doi.org/10.3969/j.issn.1004-3365.2005.04.018

IF: 1.992

2005-01-01

Microelectronics Journal

Abstract:Modern wireless communication requires that the frequency synthesizer should have fast settling time, small channel width and low phase noise. Fractional-N frequency synthesizer is widely used due to its excellent performance in these aspects. Design techniques for CMOS Fractional-N frequency synthesizers are systematically discussed in the paper. Finally, the research direction of the frequency synthesizer, as well as challenges in the development, is analyzed in brief.
An 11.1-to-14.9ghz Digital-Integral Hybrid-Proportional Fractional-N PLL with an LC DTC Achieving 0.52μs Locking Time and 41.3f5 Jitter

Hongzhuo Liu,Wei Deng,Haikun Jia,Baoyong Chi

DOI: https://doi.org/10.1109/cicc60959.2024.10529102

2024-01-01

Abstract:With the abundance of mm-wave bands and a drastically increased number of devices, new generations of wireless communication and cognitive radio call for better agility and quality of frequency synthesizers. The bang-bang digital PLLs (BBPLL) become popular for its omission of the bulky analog loop filter and the flexibility to implement bandwidth gear shifting (BWGS), and some of the fast-lock and low-jitter BBPLLs have been reported [1]–[3]. However, the nonlinearity of the bang-bang phase detectors (BBPD) caused quantization noise, which degrades the phase noise (PN) performance. The analog PLLs [4], [5], on the contrary, have linear components and well-defined loop parameters, but suffer the inability of fast locking. Moreover, most of the existing fast-lock BBPLLs are based on PLL's integrator and the logics adjust the tuning word incrementally, which caused a long time for wideband hopping. The adaptive frequency switching [1] has the ability to predict the tuning word in a short time by estimating the DCO tuning gain, but it relies on the linearity of the code-frequency curve of the DCO.
A 0.8–4.2 GHz Monolithic All-Digital PLL Based Frequency Synthesizer for Wireless Communications

Zhao Yuanxin,Gao Yuanpei,Li Wei,Li Ning,Ren Junyan

DOI: https://doi.org/10.1088/1674-4926/36/1/015001

2015-01-01

Abstract:A 0.8-4.2 GHz monolithic all-digital PLL based frequency synthesizer for wireless communications is successfully realized by the 130 nm CMOS process. A series of novel methods are proposed in this paper. Two band DCOs with high frequency resolution are utilized to cover the frequency band of interest, which is as wide as 2.5 to 5 GHz. An overflow counter is proposed to prevent the "pulse-swallowing" phenomenon so as to significantly reduce the locking time. A NTW-clamp digital module is also proposed to prevent the overflow of the loop control word. A modified programmable divider is presented to prevent the failure operation at the boundary. The measurement results show that the output frequency range of this frequency synthesizer is 0.8-4.2 GHz. The locking time achieves a reduction of 84% at 2.68 GHz. The best in-band and out-band phase noise performances have reached -100 dBc/Hz, and -125 dBc/Hz respectively. The lowest reference spur is -58 dBc.
Design of high frequency PLL circuit based on wireless transceiver

Yan Gao,Wentian Cao,Zongwu Liu

DOI: https://doi.org/10.3969/j.issn.1000-8519.2017.20.005

2017-01-01

Abstract:In the wireless transceiver circuit,except for transmitter and receiver,there is a very important part is the local oscillator circuit.In order to ensure the stability of the local oscillation frequency of the output signal module and low phase noise,usually the vibration using PLL technology to achieve,especially in the field of wireless communications.This paper expounds the the basic structure and working principle of the phase-locked loop.
A 1.1 GHz CMOS Fractional-N Frequency Synthesizer with a 3b 3Rd-Order /spl Delta//spl Sigma/ Modulator

Woogeun Rhee,Ali, A.,Bang-Sup Song

DOI: https://doi.org/10.1109/isscc.2000.839747

2000-01-01

Abstract:Fractional-N frequency synthesis based on /spl Delta//spl Sigma/ modulators offers wide bandwidth with narrow channel spacing and alleviates PLL design constraints for phase noise and reference spur. However, the synthesizer phase noise performance is significantly affected by the high-frequency out-of-band noise, which is difficult to suppress with the finite number of PLL loop filter poles. This work uses a 3b 3rd-order modulator that generates less high-frequency noise and makes the system less sensitive to the phase detector nonlinearity.
An 8-14Ghz 180Fs-Rms DTC-Less Fractional ADPLL with ADC-Based Direct Phase Digitization in 40nm CMOS

Yizhuo Wang,Hao Xu,Guoyu Li,Shuai Liu,Yan Liu,Rui Yin,Hui Pan,Na Yan

DOI: https://doi.org/10.1109/cicc60959.2024.10529006

2024-01-01

Abstract:Wide frequency coverage phase locked loops (PLL) with fine frequency resolution and low phase noise are one of the most critical building blocks for the high speed communication systems. Voltage domain quantization scheme employing ADCs has been proposed in previous fractional-N PLLs as an alternative to DTC-based quantization cancellation. However, though the voltage-domain quantization is linear in modern processes, the potential nonlinearity in the time-to-voltage conversion preceding the ADC results in fractional spurs and noise folding, which will severely degrade the PLL output if not properly addressed. One approach applies linearity compensation that often requires sophisticated digital processing [1]–[2]. The other approach utilizes digital-to-time converters (DTC) or digital-to-analog converters (DAC) to generate a replica of the divider quantization noise and then cancels out this noise in the analog domain before it propagates into the loop [3]–[4], thus relaxing the requirement for linear phase detection range. Prior arts have achieved remarkable phase noise performances, at the cost of significantly higher design complexity. This work describes a wideband fractional-N PLL that uses an integrator-based time-to-voltage converter and a 10-bit SAR ADC for direct phase error digitization as shown in Fig. 1. Without linearity calibration or DTC/DAC-based quantization noise cancellation, the proposed PLL achieves low fractional spur and low jitter across a wide frequency range.
Technology-friendly phase-locked loops

Ni Xu,Zhuo Zhang,Yuanfeng Sun,Woogeun Rhee,Zhihua Wang

DOI: https://doi.org/10.1109/MWSCAS.2011.6026307

2011-01-01

Abstract:This paper presents recent architectures of the phase-locked loop (PLL) systems which relax technology dependency and provide robust, low-cost frequency generation. The first part of the paper discusses architecture advantages of the dual-path PLL which significantly reduces loop bandwidth variation. The second part of the paper reviews recent hybrid PLL architectures which do not employ the time-to-digital converter (TDC) but still offer technology scalability and leakage current immunity.
A 2.6ghz ΔΣ Fractional-N Bang-Bang PLL with FIR-Embedded Injection-Locking Phase-Domain Low-Pass Filter

Liqun Feng,Woogeun Rhee,Zhihua Wang

DOI: https://doi.org/10.1109/cicc57935.2023.10121264

2023-01-01

Abstract:The all-digital fractional-N bang-bang PLL (BBPLL) enables low-complexity frequency generation and modulation but requires a high-resolution digital-to-time converter (DTC) to mitigate in-band noise degradation caused by a nonlinear bang-bang phase detector (BBPD) [1]. The high-resolution DTC, however, is highly sensitive to PVT variations and requires complex nonlinearity calibration or compensation methods [2]. Even with the complex calibration, an inverter-based DTC is vulnerable to a sudden supply jump due to onchip digital switching noise in SoC design and has difficulty in achieving good time resolution with low-voltage design. This work presents a DTC-free ΔΣ fractional-N BBPLL using an FIR-embedded injection-locking (FIR-IL) phase-domain low-pass filter (PDLPF) with following advantages. (1) It effectively attenuates the quantization noise, suppresses noise aliasing by the second divider and improves the in-band phase noise of the BBPLL. (2) It achieves good fractional spur performance even without nonlinearity calibration. (3) Not sensitive to mismatches and nonlinearity, it is suitable for low-voltage design with advanced CMOS technology.
A Low-Power and Small Chip-Area Fractional-N Digital PLL with Combination of DPI and TDC

Hangyan Guo,Fan Yang,Zherui Zhang,Runhua Wang,Junhua Liu,Huailin Liao

DOI: https://doi.org/10.1109/icsict.2016.7998979

2016-01-01

Abstract:This paper presents a novel fractional-N digital PLL structure with a digitally controlled phase interpolator (DPI) and a time-to-digital converter (TDC). In this structure, a short bit-width DPI and a short bit-width TDC are combined to achieve high phase resolution and low in-band phase noise. Moreover, since the DPI readily achieves 360° phase range and the TDC provides good linearity, no extra complex calibration is needed, which simplifies the design and saves power and chip area. Designed in a 55-nm CMOS technology, the proposed digital PLL achieves -103 dBc/Hz in-band phase noise at 2.4 GHz output frequency. It consumes 2.4 mW from a 1.2-V supply and occupies 0.18 mm2 active chip area.

Phase-locked Frequency Synthesis and Modulation for Modern Wireless Transceivers

A Fractional-N PLL for Multiband (0.8–6 GHz) Communications Using Binary-Weighted D/A Differentiator and Offset-Frequency Δ-Σ Modulator

A Low Power Sub-GHz PLL with Optimized LO Distribution Circuit

A Compact 0.8–6ghz Fractional-N PLL with Binary-Weighted D/A Differentiator and Offset-Frequency Δ−Σ Modulator for Noise and Spurs Cancellation

A Low Phase Noise, Wideband and Compact CMOS PLL for Use in a Heterodyne 802.15.3c Transceiver

A Low Power Sub-GHz PLL with Optimized Class-C Voltage-controlled Oscillator

Multi-chip Phase Synchronization Circuit of Fractional-N PLL

Phase-Locked Frequency Generation and Clocking: Architectures and Circuits for Modern Wireless and Wireline Systems

Fractional-N frequency synthesis: Overview and design perspectives

Session T1A: Tutorial: Phase-locked clock generation for SoC: Circuit and system design aspects

Fractional-N Frequency Synthesis: Overview and Practical Aspects with Fir-Embedded Design

14.1 A 0.048mm2 3mW synthesizable fractional-N PLL with a soft injection-locking technique

Design Techniques for CMOS Fractional-N Frequency Synthesizer

An 11.1-to-14.9ghz Digital-Integral Hybrid-Proportional Fractional-N PLL with an LC DTC Achieving 0.52μs Locking Time and 41.3f5 Jitter

A 0.8–4.2 GHz Monolithic All-Digital PLL Based Frequency Synthesizer for Wireless Communications

Design of high frequency PLL circuit based on wireless transceiver

A 1.1 GHz CMOS Fractional-N Frequency Synthesizer with a 3b 3Rd-Order /spl Delta//spl Sigma/ Modulator

An 8-14Ghz 180Fs-Rms DTC-Less Fractional ADPLL with ADC-Based Direct Phase Digitization in 40nm CMOS

Technology-friendly phase-locked loops

A 2.6ghz ΔΣ Fractional-N Bang-Bang PLL with FIR-Embedded Injection-Locking Phase-Domain Low-Pass Filter

A Low-Power and Small Chip-Area Fractional-N Digital PLL with Combination of DPI and TDC