Abstract:The cold rolling and intermediate annealing process, along with the incorporation of rare earth elements, play an important role in the microstructure, texture, and inhibitors of oriented silicon steel. Currently, there is limited research on the impact of rare earth yttrium on texture evolution during the cold rolling and intermediate annealing processes. Therefore, the effects of different cold rolling deformations and intermediate annealing temperatures on the microstructure and texture of Y bearing oriented silicon steel have been studied. The experimental results demonstrate that the average grain size of the intermediate annealed plate progressively decreases with increasing the cold rolling deformation. This is because the high cold rolling deformation brings more additional dislocations and distortions, consequently enhancing the driving force for recrystallization. Observing the microstructure with various cold rolling deformation, the results show that the annealed plate with a 72 % reduction rate exhibited the highest Goss texture percentage of 4.83 %. This is because the cold-rolled sheet with a reduction rate of 72 % exhibits an abundance of Goss oriented substructures. These substructures quickly dominate the {111} deformed matrix during the initial recrystallization, and promote grains nucleation and growth. As the annealing temperature increases, the driving force for the growth of recrystallized grains also increases, leading to a gradual increase in grain size. The plate annealed at 940 °C exhibits the highest percentage (4.83 %) of Goss texture. The addition of rare earth Y can lead to an increase in grain size in the intermediate annealed plate and facilitate the formation of {411} texture. This is advantageous for the abnormal growth of Goss texture. The results demonstrate that a cold rolling deformation rate of 72 % and an intermediate annealing temperature of 940 °C are good for promoting abnormal growth of Goss orientation. The study results on precipitation kinetics suggests that the grain boundary nucleation of AlN and dislocation nucleation of MnS are the most effective way of nucleation. The precipitates in oriented silicon steel without Y are Al 2 O 3 and MnS, while those in the samples with Y are AlN, YS, and YO x S y . The addition of rare earth Y leads to a reduction in both the density and size of precipitates. Moreover, With the increase of annealing temperature, the size of precipitates decreases and the amount of precipitates increases. Additionally, the addition of Y makes the steel more clean, meanwhile, the pinning effect of inclusions on grain boundaries is weakened. Therefore, the grain size of the steel with Y is larger.

The Effect of Trace Y on the Textures and Deep-drawing Ears in High Purity Aluminum

Influence Of Trace Re And Annealing On The Recrystallization Textures Of High Purity Al Anode Foils

Deformation-texture evolution in deep drawing of cold-rolled 3104 aluminum alloy sheet

Effect of Direction Change of Shear Deformation on the Textures in Rolled High Purity Al

Effect of different deformation and annealing procedures on non-magnetic textured Cu60Ni40 alloy substrates

Effects of microstructure and texture on the deep drawability of C10200 copper sheets

Multi-scale numerical investigation of deep drawing of 6K21 aluminum alloy by crystal plasticity and a stress-invariant based anisotropic yield function under non-associated flow rule

Influence Of Recrystallization Annealing On The Cube Texture In High-Purity Aluniinuni Foils

Effect of Residual Deformation Energy and Critical Heating Rate on Cubic Texture and Grain Growth Behavior of Severely Deformed Aluminum Foil

Effect of intermediate annealing temperature and cold rolling deformation on the texture of yttrium bearing oriented silicon steel

Influence of Y Content and T6 Heat Treatment on the Organization and Mechanical Properties of Cast A356 Aluminum Alloy

Microstructure and texture transformation of unidirectional rolled 3% Y 2 O 3p /ZGK200 composites during annealing

Effect of Microstructure on the Dimensional Stability of Extruded Pure Aluminum

Effect of texture types on microstructure evolution and mechanical properties of AZ31 magnesium alloy undergoing uniaxial tension deformation at room temperature

Effect of Low Temperature Annealing on Surface Shear Textures of Aluminum Sheet Processed Accumulative Roll Bonding

Effect of Rolling and Annealing on Microstructure and Mechanical Properties of High Purity Aluminum

New insight of texture and microstructure evolution, and the connections between with tensile performance in as-annealed Al-Cu-Mg-Zr sheet

Effect of annealing treatment on texture evolution, microstructure and mechanical properties of an extruded Mg-Gd-Zn-Zr alloy

Effects Of Electric Field Annealing On Recrystallization Texture And Plastic Strain Ratio (R Value) Of If Steel Sheet

Effect of rare earth Y on microstructure and texture of oriented silicon steel during hot rolling and cold rolling processes

Effect of annealing process on microstructure and mechanical properties of precipitated phase of A1235 aluminum alloy