Abstract:Heat-affected zones (HAZs) in real welds are usually quite narrow, and consequently most standard mechanical tests are difficult or even impossible. Therefore, simulated microstructures are often used for mechanical tests. However, the most often used weld thermal cycle simulator produces only a few millimeters wide area of simulated microstructure in the middle of specimens. Consequently, these kind of simulated specimen are not suitable for standard tensile tests, and even for Charpy impact tests, the simulated area can be too narrow. Therefore, to investigate the mechanical properties of a fine-grain heat-affected zone in 18CrNiMo7-6 steel, two methods were used for simulation of as-welded microstructures: (a) a weld thermal cycle simulator, and (b) as an alternative, though not yet verified option, austenitizing in a laboratory furnace + water quenching. The microstructures were compared and mechanical properties investigated. The grain sizes of the simulated specimens were 10.9 μm (water-quenched) and 12.6 μm (simulator), whereby the deviations from the real weld were less than 10%. Both types of simulated specimen were used for hardness measurement, Charpy impact tests, and fatigue tests. Water-quenched specimens were large enough to enable standard tensile testing. A hardness of 425 HV, yield strength Rp02 = 1121 MPa, tensile strength Rm = 1475 MPa, impact energy KV = 73.11 J, and crack propagation threshold ΔKthR = 4.33 MPa m0.5 were obtained with the water quenched specimens, and 419 HV, KV = 101.49 J, and ΔKthR = 3.4 MPa m0.5 with the specimens prepared with the simulator. Comparison of the results confirmed that the annealed and quenched specimens were suitable for mechanical tests of FG HAZs, even for standard tensile tests. Due to the use of simulated test specimens, the mechanical properties determined can be linked to the FG HAZ microstructure in 18CrNiMo7-6 steel.

Microstructure and property of simulated heat affected zone of new austenitic stainless steel 0Cr17Mn17Mo3NiN

Research on the thermal plasticity of the 18Mn-18Cr-0.77N-2Mo high nitrogen austenitic stainless steel

Effect of Heat Input on Microstructure and Properties in Heat Affected Zone of Astm A572 Gr.65 Steel

The Dominant Role of Recrystallization and Grain Growth Behaviors in the Simulated Welding Heat-Affected Zone of High-Mn Steel

Effect of heat input on the microstructure and mechanical properties of the simulated coarse-grained heat-affected zone (CGHAZ) of novel twining-induced plasticity(TWIP) steel

Effect of Heat Input on Austenite Reversion, Recrystallization, and Ensuing Impact Toughness in Simulated Intercritical Coarse‐Grained Heat Affected Zone of Medium Mn Steel

Mechanism of Interfacial Microstructure Evolution of G115 Steel in Simulated Heat Affected Zone

Simulation and Mechanical Properties of Fine-Grained Heat-Affected Zone Microstructure in 18CrNiMo7-6 Steel

Significant influence of heat input on microstructure evolution and mechanical properties of the simulated CGHAZ in a 1000 MPa grade ultra-high strength steel

Improvement of impact toughness by microstructure refinement of simulated CGHAZ through enhancing welding heat input of low carbon Mo-V-Ti-N-B steel

Effect of Niobium Content on the Microstructure and Mechanical Properties of Simulated Coarse-Grained Heat-Affected Zone (CGHAZ) of High-Strength Low-Alloy (HSLA) Steels

Microstructure and Local Mechanical Properties of the Heat-Affected Zone of a Resistance Spot Welded Medium-Mn Steel

Microstructure and Properties of Coarse Grain Zone in Single-Pass Welding of V-N Microalloyed Steel

Microstructure and Mechanical Properties of Simulated Unaltered Coarse Grained Heat Affected Zones of 10crni3mov Steel by Double-Sided Double Arc Welding

Microstructure and mechanical properties of thermal simulation CGHAZ of DP780 high strength steel

Elucidating the heat input on CGHAZ microstructure and its irregular effect on impact toughness for a novel V-N microalloying weathering steel

Simulated Coarse Grain Heat‐Affected Zone Transformation Behavior of Newly Developed Zr–Ti–RE Deoxidized High‐Strength Low‐Alloy Steels with Extremely High Impact Toughness

N-induced Microstructure Refinement and Toughness Improvement in the Coarse Grain Heat-Affected Zone of a Low Carbon Mo–V–Ti–B Steel Subjected to a High Heat Input Welding Thermal Cycle

Effect of welding heat input on microstructure and impact toughness in CGHAZ of X100Q steel

Effect of Initial Microstructure on the Toughness of Coarse-Grained Heat-Affected Zone in a Microalloyed Steel

Abnormal Grain Growth in the Heat Affected Zone of Friction Stir Welded Joint of 32Mn-7Cr-1mo-0.3n Steel During Post-Weld Heat Treatment