Abstract:Based on gradient control of carbon partitioning between martensite and austenite during heat treatment of steels, a stepping-quenching-partitioning (S-Q-P) process is developed for high strength steels. The S-Q-P process involves several quenching processes at progressively lower temperatures between martensite-start ( M s ) and martensite-finish ( M f ) temperatures, each followed by a partitioning treatment at either the initial quenching temperature or above that temperature. A novel microstructure is designed based on the S-Q-P process. Sizes and distributions of retained austenite and high-carbon martensite surrounded by martensite laths can be manipulated by the partitioning duration and temperature, and quenching temperature of the S-Q-P process. Alloying element Si is employed in the S-Q-P steel to suppress formation of carbides and create suitable amount of retained austenite. A steel of 0.39C-1.22Mn-1.12Si-0.23Cr (wt.%) treated by the S-Q-P process is endowed with some special microstructural characteristics: some strips of retained austenite located at edges of martensite blocks with high density of dislocations and between martensite laths, some small blocks of twinned martensites distributed among bundles of the low-carbon martensite lath. The mechanical properties of the medium carbon steel after the S-Q-P process can reach ultimate tensile strength ( Rm ) of 1240 MPa, total elongation ( EI ) of 25%, and product of strength and ductility ( PSD ) of 31.2 GPa% that are much more improved than those after the conventional quenching-tempering (Q-T) and currently prevailing quenching-partitioning (Q-P) treatments. The PSD of the tested steel after the S-Q-P process increases by 67% and 32% as compared with those after the Q-T and Q-P processes, respectively.

Finite Element Simulation of Quenching and Partitioning Steel Sheets Forming

Modelling of Q&P Steel Heat Treatment Process Based on Finite Element Method

Study on the Mechanical Behavior of Quenching and Partitioning Sheet Steel and Its Application to Stamping of a Hinge Pillar Inner Panel

Simulation Analysis of Quenching Process of High Strength Steel Based on ABAQUS

Evolving asymmetric yield surfaces of quenching and partitioning steels: Characterization and modeling

Effect of alloying and microstructure on formability of advanced high-strength steels processed via quenching and partitioning

Quasi-Situ Characterization of Retained Austenite Orientation in Quenching and Partitioning Steel via Uniaxial Tensile Tests

Analysis of hydrogen-induced cracking mechanism in quenching and partitioning steels

Abnormal Strain Rate‐Dependent Work‐Hardening Behavior in Quenching and Partitioning Steel

Application of a Model for Quenching and Partitioning in Hot Stamping of High-Strength Steel

Study of Quenching and Partitioning (Q&P) and Ultrasonic Surface Rolling (USR) Process on Microstructure and Mechanical Property of a High-Strength Martensitic Steel

Simultaneous improvement of hydrogen embrittlement resistance and tensile strength of quenching and partitioning steel through dense multiple interfaces

On the role of chemical heterogeneity in phase transformations and mechanical behavior of flash annealed quenching & partitioning steels

Effect of hot stamping and quenching & partitioning process on microstructure and mechanical properties of ultra-high strength steel

A novel microstructural design and heat treatment technique based on gradient control of carbon partitioning between austenite and martensite for high strength steels

Effect of quenching-partitioning process on fatigue failure of high strength steel

Ex situ analysis of high-strength quenched and micro-alloyed steel during austenitising bending process: numerical simulation and experimental investigation

Numerical Simulation of Metal Quenching with Consideration of Influence of Temperature and Phase Transformation

Microstructure and softening of advanced high-strength steel QP1180 lap joints welded with CMT

STUDY OF FAILURE CRITERION OF ADVANCED HIGH STRENGTH STEEL