Abstract:PURPOSE The clinical failures of zirconia dental restorations are often caused by extrinsic artifacts introduced by processing. The aim of this study was to investigate the micro-defects and residual stresses generated during the multistep process of zirconia dental restorations. MATERIALS AND METHODS Thermal spray granulated 3Y-TZP powders were dry pressed by two tools exhibiting distinctly different Young's moduli, cold isostatic pressed (CIP-ed), and pressure-less fully sintered. The green bodies pressed by a stiff tool were treated with different procedures: direct milling (green milling) followed by fully sintering; half-sintering and milling (raw milling) with or without fully sintering; and fully sintering followed by grinding. The fully sintered 3Y-TZP crowns were clinically adjusted using both a diamond bur and SiC bur, respectively. Phase composition and microstructure of the pressed, milled, and ground surfaces were studied by XRD and SEM. RESULTS Tetragonal phase was the main phase of all detected 3Y-TZP specimens. Excessive residual stresses introduced by raw milling and grinding were confirmed by a strained T (111) peak, monoclinic phase, and obviously changed I(002)t /I(200)t ratio. The residual stresses would form a compressive stress layer, while it was too shallow to inhibit crack propagation even for ground specimens. Large voids with high-coordination numbers were the common packing micro-defects. Once formed, they were barely healed by CIP-ing and sintering. A stiff pressing tool was confirmed to be useful for reducing the surface packing voids. Milling removed the surface voids, but was no help for the interior ones. Raw milling introduced more serious chippings, most originating from the existing packing voids, than green milling due to its brittle failure and was less recommended for production. Grinding dense 3Y-TZP caused surface grain refinement and much more severe micro-defects, especially when clinical adjustment was applied by diamond bur compared to SiC bur. CONCLUSIONS Micro-defects and residual stresses are introduced and accumulated through the entire production chain and determine the final microstructure of zirconia dental restorations. Several procedural improvements are offered and expected to reduce processing micro-defects.

Comprehensive Performance Study on Two-spindle Denture Machining System

Effect of Machining Method and Margin Design on the Accuracy and Margin Quality of Monolithic Zirconia Crowns

Evaluation of Polycrystalline Diamond Tools in Milling of Pre-Sintered and Fully-Sintered Zirconia Ceramics

Study on milling performances of 3Y-TZP ceramics using PCD and PCBN tools

Study on PCD Tool Wear in Hard Milling of Fully-Sintered 3Y-TZP Ceramics

An Experimental Investigation on Milling Features of Fully-Sintered Zirconia Ceramics Using PCD Tools

Performance Study on Miniaturized Rapid Denture Repair System

Effect of Milling Parameters on Surface Roughness for High-Speed Milling of Pre-Sintering Zirconia

Optimization of milling process parameters of zirconia denture and its experiment

Mechanical Milling and Surface Texturing of 3Y-TZP Ceramics: A Mini Review

Optimization of Machining Parameters for Milling Zirconia Ceramics by Polycrystalline Diamond Tool

Flexural strength and Weibull analysis of Y-TZP fabricated by stereolithographic additive manufacturing and subtractive manufacturing

A critical review on sintering and mechanical processing of 3Y-TZP ceramics

Effect of Milling Speed on the Properties of Zirconia Restorations

Grinding Dental Prosthesis Using Partial Sintered Zirconia Ceramics

Experimental Investigation on Tool Wear in Ultrasonic Vibration-Assisted Turning of SiCf/SiC Ceramic Matrix Composite

Effect of Multistep Processing Technique on the Formation of Micro-Defects and Residual Stresses in Zirconia Dental Restorations.

Surface Properties of Dental 3Y-TZP with Different Treatments

Study on helical milling of small holes in zirconia ceramics with PCD tools

Comparative Study of Flexural Strength Test Methods on CAD/CAM Y-TZP Dental Ceramics

Impact of the sintering parameters on the grain size, crystal phases, translucency, biaxial flexural strength, and fracture load of zirconia materials