Abstract:ZrO 2 ceramics are commonly known as 'hard and brittle' materials due to their exceptional properties, such as high hardness, heat resistance, chemical stability, and low thermal conductivity. However, the hole processing technique for ZrO 2 ceramics often results in significant tool wear and compromises the quality of the holes. This study investigates the removal mechanism of ZrO 2 ceramic materials by using carbide tools, diamond-coated carbide tools, and micro-sintered tools. It also analyzes the impact of processing parameters on the wear mechanism of different tools and the quality of hole processing in ZrO 2 ceramics. The findings revealed that at high spindle speed (8000 r/min) and low feed rate (1 mm/min), the diamond coating on the rake surface of the diamond-coated carbide tool tends to peel off, leading to the formation of sharp edges on the flank surface. This phenomenon results in a reduction in thrust forces. Moreover, it is observed that as the number of hole machining operations increases, the peeling of the diamond coating on the tool flank becomes more severe. The increase in feed rate causes the diamond coating peeling area on the rake face of the tool to expand toward the chisel edge and even reach the thinned edge area near the chisel edge. When the feed rate of carbide tools increases, the wear degree of the chisel edge gradually increases, while the wear degree of the main cutting edge corner position gradually decreases. At low spindle speeds, the main cutting edge breaks and the cutter head is also damaged and deformed. The main wear mechanisms of micro-sintered tools involve shedding, fragmentation, wear, and adhesion of diamond abrasive grains. The bottom surface of the tool tends to accumulate a significant amount of flaky adhesion, which dulls the tool and increases thrust force. In contrast to carbide tools, diamond-coated carbide tools offer improved hole exit quality. However, micro-sintered tools often exhibit large volumes of flaking at the hole exits, resulting in shell-like stripes on the peeled surface.

Study on helical milling of small holes in zirconia ceramics with PCD tools

Helical Milling of Small Holes in Fully-Sintered Zirconia Ceramic with PCD Tools

Effect of Machining Method and Margin Design on the Accuracy and Margin Quality of Monolithic Zirconia Crowns

Optimization of Machining Parameters for Milling Zirconia Ceramics by Polycrystalline Diamond Tool

Comparative study of tool wear mechanisms in drilling ZrO2 ceramics using various tool types

Micromilling of high-aspect-ratio ceramic thin walls with customized micro PCD end mills

Study on milling performances of 3Y-TZP ceramics using PCD and PCBN tools

A Study on the Influence of Central Edge Absence in Helical Grinding for Micro-Hole Fabrication

Evaluation of Polycrystalline Diamond Tools in Milling of Pre-Sintered and Fully-Sintered Zirconia Ceramics

Kinematics and Simulation Analysis of Longitudinal-Torsional Ultrasonic Assisted Grinding of Zirconia Ceramics

Theoretical and Experimental Investigation on Inclined Ultrasonic Elliptical Vibration Cutting of Alumina Ceramics

A Machining Science Approach to Dental Cutting of Glass Ceramics Using an Electric Handpiece and Diamond Burs

Processing parameter effect, formation mechanism and inhibition method of micro-hole exit defects in rotary ultrasonic pecking drilling of SiC f /SiC composites

Cutting performance and tool wear mechanism of corrugated helical PCD tool in milling Cf/SiC composites

An Experimental Study on Rotary Ultrasonic Drilling Small-Diameter Holes of High Volume Fraction Silicon Carbide-Reinforced Aluminum Matrix Composites (Sicp/al)

Drilling process of Cf/SiC ceramic matrix composites: Cutting force modeling, machining quality and PCD tool wear analysis

A Study on the Cutting Characteristics of Bottom Abrasive Grains in Helical Grinding Tools

Experimental Study of Micro-hole Pecking Drilling in High Volume Fraction SiCp/Al7075 Composites with Variable Step Size

Critical cutting thickness model considering subsurface damage of zirconia grinding and friction–wear performance evaluation applied in simulated oral environment

Research on ultrasonic grinding ZrO2 ball valve with a cup-shaped diamond grinding wheel

Cutting performance and wear mechanism of zirconia toughened alumina ceramic cutting tools formed by vat photopolymerization-based 3D printing