Abstract:ZrO 2 ceramics are commonly known as 'hard and brittle' materials due to their exceptional properties, such as high hardness, heat resistance, chemical stability, and low thermal conductivity. However, the hole processing technique for ZrO 2 ceramics often results in significant tool wear and compromises the quality of the holes. This study investigates the removal mechanism of ZrO 2 ceramic materials by using carbide tools, diamond-coated carbide tools, and micro-sintered tools. It also analyzes the impact of processing parameters on the wear mechanism of different tools and the quality of hole processing in ZrO 2 ceramics. The findings revealed that at high spindle speed (8000 r/min) and low feed rate (1 mm/min), the diamond coating on the rake surface of the diamond-coated carbide tool tends to peel off, leading to the formation of sharp edges on the flank surface. This phenomenon results in a reduction in thrust forces. Moreover, it is observed that as the number of hole machining operations increases, the peeling of the diamond coating on the tool flank becomes more severe. The increase in feed rate causes the diamond coating peeling area on the rake face of the tool to expand toward the chisel edge and even reach the thinned edge area near the chisel edge. When the feed rate of carbide tools increases, the wear degree of the chisel edge gradually increases, while the wear degree of the main cutting edge corner position gradually decreases. At low spindle speeds, the main cutting edge breaks and the cutter head is also damaged and deformed. The main wear mechanisms of micro-sintered tools involve shedding, fragmentation, wear, and adhesion of diamond abrasive grains. The bottom surface of the tool tends to accumulate a significant amount of flaky adhesion, which dulls the tool and increases thrust force. In contrast to carbide tools, diamond-coated carbide tools offer improved hole exit quality. However, micro-sintered tools often exhibit large volumes of flaking at the hole exits, resulting in shell-like stripes on the peeled surface.

Evaluation of Polycrystalline Diamond Tools in Milling of Pre-Sintered and Fully-Sintered Zirconia Ceramics

An Experimental Investigation on Milling Features of Fully-Sintered Zirconia Ceramics Using PCD Tools

Study on PCD Tool Wear in Hard Milling of Fully-Sintered 3Y-TZP Ceramics

A Machining Science Approach to Dental Cutting of Glass Ceramics Using an Electric Handpiece and Diamond Burs

Study on milling performances of 3Y-TZP ceramics using PCD and PCBN tools

Wear Behaviors of Pcd Tools in Turning Granite

In Vitro Study on Dental Abrasive Finishing of Restorative Ceramics Using Diamond Burs in Dental Surgery

Experimental Investigation on Tool Wear in Ultrasonic Vibration-Assisted Turning of SiCf/SiC Ceramic Matrix Composite

Optimization of Machining Parameters for Milling Zirconia Ceramics by Polycrystalline Diamond Tool

Experimental investigation of coatings efficiency in micro-ball-end milling of pre-sintered 5Y-TZP ceramic

Mechanical Milling and Surface Texturing of 3Y-TZP Ceramics: A Mini Review

Comprehensive Performance Study on Two-spindle Denture Machining System

Performance and Wear Mechanisms of Polycrystalline Diamond Tools with Different Diamond Grains in Milling Cf/SiC Composites

Comparative study of tool wear mechanisms in drilling ZrO2 ceramics using various tool types

Evaluation of milling performance of 50-μm D-shaped carbide tool, polycrystalline diamond-coated carbide tool, and polycrystalline diamond tool

Study of non-brittle removal mechanism in grinding of polycrystalline diamond compact

Tribological Behavior and Cutting Performance of Monolayer, Bilayer and Multilayer Diamond Coated Milling Tools in Machining of Zirconia Ceramics

Research Advances on Primary Machining Technologies of Zirconia Ceramics

Helical Milling of Small Holes in Fully-Sintered Zirconia Ceramic with PCD Tools

Effect of Milling Parameters on Surface Roughness for High-Speed Milling of Pre-Sintering Zirconia

Study on helical milling of small holes in zirconia ceramics with PCD tools