Abstract:PURPOSE The clinical failures of zirconia dental restorations are often caused by extrinsic artifacts introduced by processing. The aim of this study was to investigate the micro-defects and residual stresses generated during the multistep process of zirconia dental restorations. MATERIALS AND METHODS Thermal spray granulated 3Y-TZP powders were dry pressed by two tools exhibiting distinctly different Young's moduli, cold isostatic pressed (CIP-ed), and pressure-less fully sintered. The green bodies pressed by a stiff tool were treated with different procedures: direct milling (green milling) followed by fully sintering; half-sintering and milling (raw milling) with or without fully sintering; and fully sintering followed by grinding. The fully sintered 3Y-TZP crowns were clinically adjusted using both a diamond bur and SiC bur, respectively. Phase composition and microstructure of the pressed, milled, and ground surfaces were studied by XRD and SEM. RESULTS Tetragonal phase was the main phase of all detected 3Y-TZP specimens. Excessive residual stresses introduced by raw milling and grinding were confirmed by a strained T (111) peak, monoclinic phase, and obviously changed I(002)t /I(200)t ratio. The residual stresses would form a compressive stress layer, while it was too shallow to inhibit crack propagation even for ground specimens. Large voids with high-coordination numbers were the common packing micro-defects. Once formed, they were barely healed by CIP-ing and sintering. A stiff pressing tool was confirmed to be useful for reducing the surface packing voids. Milling removed the surface voids, but was no help for the interior ones. Raw milling introduced more serious chippings, most originating from the existing packing voids, than green milling due to its brittle failure and was less recommended for production. Grinding dense 3Y-TZP caused surface grain refinement and much more severe micro-defects, especially when clinical adjustment was applied by diamond bur compared to SiC bur. CONCLUSIONS Micro-defects and residual stresses are introduced and accumulated through the entire production chain and determine the final microstructure of zirconia dental restorations. Several procedural improvements are offered and expected to reduce processing micro-defects.

Impact of Hard Machining on Zirconia Based Ceramics for Dental Applications

Effect of Machining Method and Margin Design on the Accuracy and Margin Quality of Monolithic Zirconia Crowns

Effect of Multistep Processing Technique on the Formation of Micro-Defects and Residual Stresses in Zirconia Dental Restorations.

Characterization of Zirconia-Based Ceramics After Microgrinding

Advances and challenges in zirconia-based materials for dental applications

On the behaviour of zirconia-based dental materials: A review

A review on surface texturing of zirconia ceramics for dental applications

Evaluation of Polycrystalline Diamond Tools in Milling of Pre-Sintered and Fully-Sintered Zirconia Ceramics

Strength-limiting damage and its mitigation in CAD-CAM zirconia-reinforced lithium-silicate ceramics machined in a fully crystallized state

Sliding contact wear and subsurface damage of CAD/CAM materials against zirconia

Advances in ceramics for tooth repair: From bench to chairside

Zirconia in fixed implant prosthodontics

Zirconia toughened fluorosilicate glass-ceramics for dental prosthetic restorations

Effect of Milling Speed on the Properties of Zirconia Restorations

Hydrothermal Ageing and Its Effect on Fracture Load of Zirconia Dental Implants

Laser surface texturing of zirconia-based ceramics for dental applications: A review

An overview of zirconia ceramics: Basic properties and clinical applications

INFLUENCE OF HEAT TREATMENT AND IN-VITRO AGING ON MECHANICAL PROPERTIES AND SURFACE ROUGHNESS OF COLD ISOSTATIC PRESSED ZIRCONIA - AN INVITRO STUDY

Fatigue Behaviours of the Zirconia Dental Restorations Prepared by Two Manufacturing Methods

Evaluation of zirconia ceramics fabricated through DLP 3d printing process for dental applications

Novel Zirconia Materials in Dentistry