Abstract:The balance piston seal in multiple-stage centrifugal compressors and axial turbines sustains the largest pressure drop through the machines and therefore plays an important role in successful full load operation at high rotational speed. This is especially true for power dense turbomachines in supercritical CO2 power cycles that generate or expend higher fluid pressures (above the critical value 7.3 MPa) and density (close to water 1000 kg/m(3)), because the fluid forces generated by the balance piston seals are directly proportional to the fluid density and the pressure drop across the seal. This paper presents a comprehensive assessment and comparison on the leakage and rotordynamic performance of three types of annular gas seals for application in a 14 MW supercritical CO2 turbine. These three seals represent the main seal types used in high-speed rotating machines at the balance piston location in efforts to limit internal leakage flow and achieve rotordynamic stability, including a labyrinth seal (LABY), a fully partitioned pocket damper seal (FPDS), and a hole-pattern damper seal (HPS). These three seals were designed to have the same sealing clearance and similar axial lengths. To enhance the seal net damping capability at high inlet preswirl condition, a straight swirl brake was also designed and employed at seal entrance for each type seal to reduce the seal inlet preswirl velocity. Numerical results of leakage flow rates, rotordynamic force coefficients, cavity dynamic pressure, and swirl velocity developments were analyzed and compared for three seal designs at high positive inlet preswirl (in the direction of shaft rotation), using a proposed transient computational fluid dynamic (CFD)-based perturbation method based on the multiple-frequency elliptical-orbit rotor whirling model and the mesh deformation technique. To take into account of real gas effect with high accuracy, a table look-up procedure based on the National Institute of Standards and Technology reference fluid properties database was implemented, using an in-house code, for the fluid properties of CO2 in both supercritical and subcritical conditions. Results show that the inlet swirl brake can significantly reduce the preswirl velocity at seal entrance, lowering the effective damping crossover frequency f co (or even f co = 0) to maximize the full operational frequency range of the machines. In stability analysis phase of a MW-scale supercritical CO2 turbine/compressor, the seal stiffness effects on the rotor mode shape must be evaluated carefully, where the seal stiffness is sufficiently large (comparable to the bearing stiffness). From a rotordynamic viewpoint, the HPS seal with entrance swirl brake is a better seal concept for the balance piston seal in supercritical CO2 turbomachinery, which possesses the largest positive effective damping throughout the entire subsynchronous frequency range.

Research and Design of Packing of High Pressure CO2 Compressors

Experimental Study on Dynamic Sealing Performance under High Pressure and High Speed

Experimental Research and Finite Element Analysis of Seals in the Pressure Compensator

Experimental Study on Frictional and Sealing Performances of Packing Rings in an Oil-Free Gas Compressor

Numerical Investigation for Windage Loss and Flow Characteristics Analysis with Supercritical CO2 in Labyrinth Seal

Design and Performance Research of Single Rubber Cylinder for High Pressure Gas Injection Packer

Experimental investigation on a two-stage CO2 compressor with high back pressure

Numerical Study on Sealing Performance after Wear of Plug Valve During Opening–closing Process

Numerical study on sealing performance of supercritical carbon dioxide compressor dry gas seal

Mechanical Behavior and Structure Optimization of Compressed PHP Packer Rubber

Numerical Investigation on the Effects of Structural Parameters of Labyrinth Cavity on Sealing Performance

Leakage and Rotordynamic Characteristics for Three Types of Annular Gas Seals Operating in Supercritical CO2 Turbomachinery

An improvement of labyrinth seal in shroud of centrifugal compressor with low flow coefficient

Thrust Load Adjustment and Seal Improvement of Centrifugal Compressor

Experimental Studies on CO2 Corrosion of Rubber Materials for Packer under Compressive Stress in Gas Wells

Turbulence Dissipation of Leakage Flow in Supercritical CO2 Labyrinth Seals

Design of Packing Cup Interference Fit Value of Hypercompressors for Low Density Polyethylene Production

IMPROVING THE SEALING EFFECT OF AN ECCENTRIC DOUBLE-DOOR HYDRAULIC PACKER

Design and Finite Element Analysis of Composite PTFE Compression Packing with C-shape Structure

Numerical Investigation on Labyrinth Seal Leakage Flow and Its Effects on Aerodynamic Performance for a Multistage Centrifugal Compressor

Design Method of Interference Fit in Packing Cups of Hypercompressors