Abstract:The modern compressor operation is challenged by the liquid presence in wet gas operating conditions. The liquid phase may affect the compressor stability by partially flooding the internal annular gas seals and inducing subsynchronous vibration (SSV). To improve the annular seal behavior and increase the rotor stability, high-precision results of leakage flow rates and rotordynamic force coefficients are needed for annular gas seals in wet gas conditions. In order to better understand the leakage and rotordynamic characteristics of the annular gas seal in wet gas conditions, a 3D transient CFD-based perturbation method was proposed for computations of leakage flow rates and rotordynamic force coefficients of annular gas seals with liquid phase in main gas phase, based on inhomogeneous Eulerian-Eulerian multiphase flow model, mesh deformation technique, and the multifrequency rotor whirling orbit model. Numerical results of frequency-dependent rotordynamic force coefficients and leakage flow rates were presented and compared for three types of noncontact annular gas seals, which include a smooth plain annular seal (SPAS), a labyrinth (LABY) seal, and a fully partitioned pocket damper seal (FPDS). These three seals were designed to have the identical rotor diameter, sealing clearance, and axial length. The accuracy and the availability of the present transient CFD numerical method were demonstrated with the experiment data of leakage flow rates and frequency-dependent rotordynamic force coefficients of the smooth plain seal with four inlet liquid volume fractions (LVFs) of 0%, 2%, 5%, and 8%. Steady and transient numerical simulations were conducted at inlet air pressure of 62.1 bar, pressure ratio of 0.5, rotational speed of 15,000 rpm, and inlet preswirl ratio of 0.3 for four inlet LVFs varying from 0% to 8% and 14 subsynchronous and synchronous whirling frequencies up to 280 Hz. The numerical results show that the inlet liquid phase has a significant influence on the leakage and rotordynamic coefficients for all three types of annular gas seals. The mixture leakage flow rate increases with the increasing inlet LVF, combining the decreasing gas-phase and linearly increasing liquid-phase leakage flow rates. The smooth plain seal leaks the most gas phase and liquid phase, followed by the pocket damper seal (PDS) and then the labyrinth seal. Increasing inlet LVF significantly decreases the direct stiffness and slightly increases the effective damping of the smooth plain seal. The labyrinth seal possesses evident negative direct stiffness and shows a noticeable decreasing effective damping with the increasing inlet LVF at the subsynchronous frequency range. Increasing inlet LVF obviously increases all the force coefficients of the pocket damper seal including the positive effective damping. From a rotordynamic viewpoint, the FPDS possesses a better liquid tolerant capability and so is a better sealing scheme for the balance piston seals and center seals of the centrifugal compressor in wet gas operating condition.

Prediction of gas flow in compressible and low permeability porous media

Investigating the influence of operating variables on sealing performance of a V-ring seal stack in the oil and gas industry for enhanced environmental and operational performance

Numerical Study on Sealing Performance after Wear of Plug Valve During Opening–closing Process

A Non-Ideal Geometry Based Prediction Approach of Fitting Performance and Leakage Characteristic of Precision Couplings.

Numerical Investigation on the Leakage and Rotordynamic Characteristics for Three Types of Annular Gas Seals in Wet Gas Conditions

Influence of Gas Condensability on Labyrinth Seal's Sealability

Gas Leakage Prediction of Contact Interface in Fabric Rubber Seal Based on a Rectangle Channel Model

Leakage prediction approach and influencing factor analysis from seal test

Study on a Type of Low-Leakage Brush Seal Porous Media Model

A Percolation Method of Leakage Calculation and Prediction Within the Mechanical Seal Interface

Theoretical and Experimental Analysis of a Non Contacting Elastohydrodynamic Sealing

Leakage Simulation and Prediction for High-Pressure Natural Gas Pipeline in a Confined Space

Air Leakages at Microvalves: Pressure Decay Measurements and Extended Continuum Modelling of Knudsen Flows

Gas Permeability Calculation of Tight Rocks Based on Laboratory Measurements with Non-Ideal Gas Slippage and Poroelastic Effects Considered

Securing offshore resources development: A mathematical investigation into gas leakage in long-distance flexible pipes

Prediction of Time-Correlated Leakage Rates of Bolted Flanged Connections by Considering the Maximum Gasket Contact Stress

Performance Analysis of a Pressurized Assembly with a Reinforced O-ring

Numerical investigation of gas permeation and condensation behavior of flexible risers

Gas Leakage Evaluation of Metallic Sealing Surfaces with Annular Morphology

Research on internal flow field analysis and power loss modeling of the expansion seal ring

Investigation of flow field characteristics in hose pumps under various operating conditions and their impact on gap leakage