Abstract:The modern compressor operation is challenged by the liquid presence in wet gas operating conditions. The liquid phase may affect the compressor stability by partially flooding the internal annular gas seals and inducing subsynchronous vibration (SSV). To improve the annular seal behavior and increase the rotor stability, high-precision results of leakage flow rates and rotordynamic force coefficients are needed for annular gas seals in wet gas conditions. In order to better understand the leakage and rotordynamic characteristics of the annular gas seal in wet gas conditions, a 3D transient CFD-based perturbation method was proposed for computations of leakage flow rates and rotordynamic force coefficients of annular gas seals with liquid phase in main gas phase, based on inhomogeneous Eulerian-Eulerian multiphase flow model, mesh deformation technique, and the multifrequency rotor whirling orbit model. Numerical results of frequency-dependent rotordynamic force coefficients and leakage flow rates were presented and compared for three types of noncontact annular gas seals, which include a smooth plain annular seal (SPAS), a labyrinth (LABY) seal, and a fully partitioned pocket damper seal (FPDS). These three seals were designed to have the identical rotor diameter, sealing clearance, and axial length. The accuracy and the availability of the present transient CFD numerical method were demonstrated with the experiment data of leakage flow rates and frequency-dependent rotordynamic force coefficients of the smooth plain seal with four inlet liquid volume fractions (LVFs) of 0%, 2%, 5%, and 8%. Steady and transient numerical simulations were conducted at inlet air pressure of 62.1 bar, pressure ratio of 0.5, rotational speed of 15,000 rpm, and inlet preswirl ratio of 0.3 for four inlet LVFs varying from 0% to 8% and 14 subsynchronous and synchronous whirling frequencies up to 280 Hz. The numerical results show that the inlet liquid phase has a significant influence on the leakage and rotordynamic coefficients for all three types of annular gas seals. The mixture leakage flow rate increases with the increasing inlet LVF, combining the decreasing gas-phase and linearly increasing liquid-phase leakage flow rates. The smooth plain seal leaks the most gas phase and liquid phase, followed by the pocket damper seal (PDS) and then the labyrinth seal. Increasing inlet LVF significantly decreases the direct stiffness and slightly increases the effective damping of the smooth plain seal. The labyrinth seal possesses evident negative direct stiffness and shows a noticeable decreasing effective damping with the increasing inlet LVF at the subsynchronous frequency range. Increasing inlet LVF obviously increases all the force coefficients of the pocket damper seal including the positive effective damping. From a rotordynamic viewpoint, the FPDS possesses a better liquid tolerant capability and so is a better sealing scheme for the balance piston seals and center seals of the centrifugal compressor in wet gas operating condition.

Gas Leakage Evaluation of Metallic Sealing Surfaces with Annular Morphology

Effect of T-groove Parameters on Steady-State Characteristics of Cylindrical Gas Seal

Gas Sealing Performance Study of Metal W Shaped Seal Ring

An Approach to Calculate Leak Channels and Leak Rates Between Metallic Sealing Surfaces

A Measuring Method of Gas Leakage along the Contact Interface of the Stripped Rubber Seals

Study on Leakage Rate of Rubber Sealing Structures Based on Percolation Theory

A Leakage Rate Model for Metal-to-Metal Seals Based on the Fractal Theory of Porous Medium

Modeling Surface Roughness and Flow of Gases in Threaded Connections to Analyze Sealing Performance

Modelling of Fluid Permeability at the Interface of the Metal-to-Metal Sealing Surface

Research on Micro Gap Flow Field Characteristics of Cylindrical Gas Film Seals Based on Experimental and Numerical Simulation

Gas sealing behavior of gasketed segmental joints in shield tunnels: An experimental and computational study

Flow Numerical Simulation of Dry Gas Seal with Double-row Spiral Grooves

Failure Analysis and Improvement of Mechanical Seals in Underwater Turbine

Numerical Investigation on the Leakage and Rotordynamic Characteristics for Three Types of Annular Gas Seals in Wet Gas Conditions

Gas Leakage Prediction of Contact Interface in Fabric Rubber Seal Based on a Rectangle Channel Model

Evolution of Bi-Gaussian Surface Parameters and Sealing Performance for a Gas Face Seal under a Low-Speed Condition

Securing offshore resources development: A mathematical investigation into gas leakage in long-distance flexible pipes

Research Status and Development Trend of Cylindrical Gas Film Seals for Aeroengines

A Porous Media Leakage Model of Contact Mechanical Seals Considering Surface Wettability

On the Sealability of Metal-to-Metal Seals With Application to Premium Casing and Tubing Connections

Research On Fractal Heat Flow Characterization Of Finger Seal Considering The Heat Transfer Effect Of Contact Gaps On Rough Surfaces