Abstract:The balance piston seal in multiple-stage centrifugal compressors and axial turbines sustains the largest pressure drop through the machines and therefore plays an important role in successful full load operation at high rotational speed. This is especially true for power dense turbomachines in supercritical CO2 power cycles that generate or expend higher fluid pressures (above the critical value 7.3 MPa) and density (close to water 1000 kg/m(3)), because the fluid forces generated by the balance piston seals are directly proportional to the fluid density and the pressure drop across the seal. This paper presents a comprehensive assessment and comparison on the leakage and rotordynamic performance of three types of annular gas seals for application in a 14 MW supercritical CO2 turbine. These three seals represent the main seal types used in high-speed rotating machines at the balance piston location in efforts to limit internal leakage flow and achieve rotordynamic stability, including a labyrinth seal (LABY), a fully partitioned pocket damper seal (FPDS), and a hole-pattern damper seal (HPS). These three seals were designed to have the same sealing clearance and similar axial lengths. To enhance the seal net damping capability at high inlet preswirl condition, a straight swirl brake was also designed and employed at seal entrance for each type seal to reduce the seal inlet preswirl velocity. Numerical results of leakage flow rates, rotordynamic force coefficients, cavity dynamic pressure, and swirl velocity developments were analyzed and compared for three seal designs at high positive inlet preswirl (in the direction of shaft rotation), using a proposed transient computational fluid dynamic (CFD)-based perturbation method based on the multiple-frequency elliptical-orbit rotor whirling model and the mesh deformation technique. To take into account of real gas effect with high accuracy, a table look-up procedure based on the National Institute of Standards and Technology reference fluid properties database was implemented, using an in-house code, for the fluid properties of CO2 in both supercritical and subcritical conditions. Results show that the inlet swirl brake can significantly reduce the preswirl velocity at seal entrance, lowering the effective damping crossover frequency f co (or even f co = 0) to maximize the full operational frequency range of the machines. In stability analysis phase of a MW-scale supercritical CO2 turbine/compressor, the seal stiffness effects on the rotor mode shape must be evaluated carefully, where the seal stiffness is sufficiently large (comparable to the bearing stiffness). From a rotordynamic viewpoint, the HPS seal with entrance swirl brake is a better seal concept for the balance piston seal in supercritical CO2 turbomachinery, which possesses the largest positive effective damping throughout the entire subsynchronous frequency range.

Numerical Study of Leakage and Rotordynamic Performance of Staggered Labyrinth Seals Working with Supercritical Carbon Dioxide

Numerical Calculation of Nonlinear Dynamic Characteristics for Labyrinth Seals

Effects of pressure ratio and rotational speed on leakage flow and cavity pressure in the staggered labyrinth seal

Labyrinth Seal Rotordynamic Characteristics Part I: Operational Conditions Effects

Numerical comparisons of rotordynamic characteristics for three types of labyrinth gas seals with inlet preswirl

Turbulence Dissipation of Leakage Flow in Supercritical CO2 Labyrinth Seals

Leakage and Rotordynamic Characteristics for Three Types of Annular Gas Seals Operating in Supercritical CO2 Turbomachinery

Dynamic Coefficient Analysis of Labyrinth Seal Based on FLUENT

An analytical study of the effect of different eccentricity and whirling speed on labyrinth seal forces and dynamics parameters

Influence of leakage flow through labyrinth seals on rotordynamics: numerical calculations and experimental measurements

Labyrinth Seal Rotordynamic Characteristics Part II: Geometrical Parameter Effects

Leakage and critical speed effect of labyrinth seal structure

Rotordynamic Analysis and Leakage Performance Study of a Hole Diaphragm Labyrinth Seal Using the CFD Method

Leakage Flow-Induced Excitation Behavior and Rotor Instability in the High-Speed Supercritical CO2 Scallop Damper Seals

Numerical Investigation for Windage Loss and Flow Characteristics Analysis with Supercritical CO2 in Labyrinth Seal

Effects of Mushroom-Shaped Tooth Wear on the Leakage Performance and Rotordynamic Coefficients of Labyrinth Seals

Investigation on the Discharge and Windage Heating Characteristics of Staggered Labyrinth Seals under Adiabatic and Heat Transfer Models

Numerical Investigation on Flow Characteristics and Aerodynamic Performance of a 1.5-Stage SCO2 Axial-Inflow Turbine with Labyrinth Seals

Rotordynamic Characteristics of the Straight-Through Labyrinth Seal Based on the Applicability Analysis of Leakage Models Using Bulk-Flow Method

Experimental and Numerical Investigations on the Leakage Flow Characteristics of Labyrinth Seals

Numerical Comparison of Leakage Flow and Rotordynamic Characteristics for Two Types of Labyrinth Seals With Baffles