Abstract:A new selective catalytic reduction (SCR) system for captive power plants in the petrochemical industry was analyzed. The key components suitable for the target SCR system were obtained using computational fluid dynamics (CFD) numerical simulation combined with a cold physical model. The structural characteristics of the SCR system were studied, and corresponding design schemes were obtained for the key components, such as the guide plate, the ammonia injection grid (AIG), the static mixer, and the rectifier grille. The distributions of the flue gas velocity and the NH3 concentration within the flue cross-section in front of the first layer catalyst were studied in detail. Synchronously, the pressure loss and the temperature reduction characteristics in the SCR system were also considered. CFD results showed that the average standard deviation of the flue gas velocity was about 11.61%, and the average standard deviation of the NH3 concentration distribution could reach about 3.79% under the five operating conditions. It could be concluded that the uniformity of the flue gas velocity and the NH3 concentration distribution within the above flue cross-section was guaranteed by comparing to the design standard of 15% and 5%, respectively. It was further found that the maximum pressure loss between the inlet and the first layer catalyst was about 106.64 Pa, and the temperature reduction characteristic of the entire SCR system could be maintained within ±0.01 °C, which indicated that no extreme adverse effect arose due to the introduce of the key components. The cold physical model experiment was accordingly conducted to verify the reliability of the above CFD results. The cold physical model experiment results showed that the average standard deviation of flue gas velocity was about 8.82%, and the average standard deviation of NH3 concentration distribution could reach about 4.21%. The maximum biases for the standard deviations of the flue gas velocity and the NH3 concentration distribution were approximately 4.83% and 1.18% under the five operating conditions. Based on the good agreement of the research results via the two different methods, the designed key components of a new SCR system could be confirmed to be feasible, which would benefit the deNOx performance of the SCR system.

Physical and Chemical Process Model of SCR and Its Verification

Model Predictive Control Case Study: Selective Catalytic Reduction (scr) System in Coal-Fired Power Plant

Modeling and Performance Analysis of SCR DeNOx Catalyst for Reducing NOx Emissions in Diesel Engine

Fluid Mixing Optimization Strategy of Catalytic Reactor for Marine SCR System

3D Modeling of Flow, Spray of Reductant and Surface Chemical Reaction in Diesel Urea SCR-NOx Catalytic Converter

Design and Verification of Key Components of a New Selective Catalytic Reduction System in a Petrochemical Captive Power Plant

Integrated Gas and Solid Model to Determine the Flow Performance in the SCR Reactor

Development and verification of model predictive control strategy for selective catalytic reduction with rapid prototyping

Multi-Scale SCR Modeling, 1D Kinetic Analysis and 3D System Simulation

CFD analysis of influencing factors on SCR denitration efficiency of sintering flue gas based on response surface methodology

Modeling and simulation of marine SCR system based on Modelica

Influence Factors of DeNOx Behavior in Urea-SCR Catalytic Converter of Diesel

Numerical Simulation of Selective Catalytic Reduction of NO and SO2 Oxidation in Monolith Catalyst

A temporal discretization and spatial integration SCR model with dual temperature-related parameters

Simulation of the flow field and the chemical reaction coupling of selective catalytic reduction (SCR) system using an orthogonal experiment

Optimization Analysis of Various Parameters Based on Response Surface Methodology for Enhancing NOx Catalytic Reduction Performance of Urea Selective Catalytic Reduction on Cu-ZSM-13 Catalyst

Experimental and Modeling Study on the Mechanism and Sensitive Parameters of the Thermal DeNOx Process

CFD Modeling of Unsteady SCR Denox Coupled with Regenerative Heat Transfer in Honeycomb Regenerators Partly Coated by Vanadium Catalysts

Mechanism-Based Kinetic Modeling of N2o Formation on Scr Activity over Cu-Ssz-13 Catalysts for Diesel Vehicle

Large eddy simulation of hydrodynamics and deNOx process in a coal-fired power plant SCR system

Tuning the Standard SCR Reaction Kinetics to Model NO Conversion in a Diesel Engine Exhaust SCR Catalyst System Under Steady State Conditions in 1D and 3D Geometries Using Ammonia Gas as the Reductant