Voltage Transformer and Study of Its Using

Wei CHEN,Ai-hua PEI

2005-01-01

Abstract:This paper gives a brief introduction of the principle of voltage transformer and its application. The imaginable problems and the relevant trouble - shooting are especially illustrated

What problem does this paper attempt to address?

Research on Short-Circuit Vibration of Power Transformer

洪凯星,潘再平,黄海

DOI: https://doi.org/10.3969/j.issn.1001-4551.2010.06.021

2010-01-01

Abstract:Diagnose transformer using vibration method is a new trend which can monitor without shut apparatus down,but this method is still unsatisfied.The vibration signals from the transformer tank are complicated,and it is important to find a model which can reflect the vibration correctly.Aiming at how to simplify the vibration model,a transformer tank vibration model under short-circuit condition was presented.The model was based on how signal generates and how signal transmits.The model was obtained using data set sampled in single phase short-circuit tests.With the fully trained model,the estimated vibration signal at one point was calculated by employing the input current only.In order to validate the model,three phase short-circuit tests were taken.The results show a good agreement between estimated signals and measured signals,the results indicate that it is feasible to use a simplified windings and transmission model.
The Error Analysis on Voltage Transformer and Things to be Noticed

Zhao Yu-fu,Hou Hui-juan,Li Jing,Zhao Chao

2008-01-01

Abstract:The paper simply introduces working principle of capacitor voltage transformer(CVT) and induced voltage transformer(IVT).It analyzes reason to error of them and factors which affect error.And brings forward things to be noticed when voltage transformer be ploughed into operation and be operating.
Voltage Transformer Winding Impulse Over-Voltage Study

Yanwei Wen

2013-01-01

Abstract:Potential gradient distribution and surface electrical field strength distribution of voltage transformer under impulse voltage effect are import basis for its winding structure and insulation design.Taking some typical plans for examples,this paper introduced how to establish 25 kV voltage transformer's internal model,how to calculate unit parameters,and how to use ATP-EMPT electromagnetic transient calculation program to establish simulation model,to have got impulse voltage distribution of multi-plans.Analysis was made to functions of over-voltage protection measures,such as adding shielding layer,optimizing windings,connecting with metal oxide varistors(MOV),to provide references for optimizing design of voltage transformer insulation structure.
Analysis and Treatment of Electronic Voltage Transformers Exceeded Tolerance Problem

Wang Jia-Ying,Chen Hao-Lin,Li Shen-Wang,Zhang Guo-Qing,Guo Zhi-Zhong

DOI: https://doi.org/10.1109/IMCCC.2012.88

2012-01-01

Abstract:For speeding up of substation digitization processing, transformers do not need high efficiency signal output. In the high-voltage power system, the traditional voltage transformers have been gradually replaced by electronic voltage transformer. As electronic voltage transformer based on capacitive voltage divider's excellent performance, it has become the best substitute of the traditional voltage transformer, widely used in power system. This paper presented the basic structure and analysis the experiment data. The main reasons of exceed tolerance problem is RC oscillating circuit and detention electric charge. By choosing a suitable value resistance, the problem has been solved. According to IEC60044-7, the ECVT reaches the requirement. It can completely meet the demands of the development of modern power.
Analyses on an electronic voltage transformer's failure by its resonance with very fast transient overvoltage and suppression

Houda Zhu,Qing Chen,Hongbin Li,Yue Tong,Linshan Han,Yang Jiao

DOI: https://doi.org/10.1049/hve2.12370

IF: 4.967

2023-09-10

High Voltage

Abstract:As voltage measuring devices are widely used in the high voltage power system with a primary‐secondary‐fusion structure, electronic voltage transformers are directly connected to the primary conductor and would face much more serious electromagnetic environments than general secondary equipment. As a result, they would still experience failures even when general protection measures are adopted to suppress overvoltages' amplitudes. To address this issue, an innovative method is proposed after analyses are conducted on the resonance between a transformer and an overvoltage. Within this method, an air‐cored coil is installed in a transformer to artificially shift its natural frequency and to dodge the high‐frequency dominant component of a transient overvoltage, avoiding the aforementioned resonance and suppressing the secondary overvoltage. In addition, simulations and laboratory tests are conducted to prove this method's validity.

engineering, electrical & electronic
On-Load Automatic Voltage Regulation System Designed Via Thyristor for Distribution Transformer

Hongzhong Ma,Suwen Gu,Huafang Wang,Honghua Xu,Chunning Wang,Hao Zhou

DOI: https://doi.org/10.1109/icems.2017.8055967

2017-01-01

Abstract:At present, voltage regulation of no load distribution transformer is not flexible and failure rate of mechanical on-load tap-changers is high. To solve these problems, a scheme of automatic on-load voltage regulation system designed via thyristor for distribution transformer was proposed. The system improved the existing topology of on-load voltage regulation system via power electronic device and added the overvoltage protection circuit of thyristor. The prototype of automatic voltage regulation system has been tested completely. The results show that, compared with the voltage regulation system via mechanical switch, transition waveforms of voltage regulation system via thyristor are of better quality and transition time is shorter.
Novel Progress in the Research of Piezoelectric Transformer

Liyang YU,Shurong DONG,Demiao WANG

DOI: https://doi.org/10.3969/j.issn.1000-3819.2006.02.028

2006-01-01

Abstract:Based on the physical theory,the operating principle of piezoelectric transform is introduced.Some typital peizoelectric transformers are reviewed.Combined with the method of the design on device,the characteristic and the domain of application are analyzed.Basis on the above analysis,the miniature peizoelectric transformer is expected, and the problem in the progress of miniature peizoelectric transformer is presented.
Research on Medium-voltage Electronic Transformers

万雄,张贵新,王强,王鹏

2009-01-01

Abstract:The electronic transformers have a series of problems in testing and operation.This paper discusses the saturation characteristics of electronic current transformer and the temperature characteristics of electronic voltage transformer.Current transformer with nonlinear excitation characteristics usually includes a closed-core.It can not work in transient process because of core saturation.This paper analyzes the features of the current transformer with non-magnetic air gap.The principle and structure of the electronic voltage transformer based on voltage divider are introduced,and the factors affecting its temperature characteristic are analyzed.Hence,a method of temperature compensation via thermistor is presented to enhance the temperature stability of the medium-voltage electronic transformers.
Research on Typical Power Supply Modes of Middle and Low Voltage Transformer Areas at Home and Abroad

Jieyun ZHENG,Chunyi HUANG,Guilian WU,Siwei HOU,Yang LIU,Jicun WANG,Chengmin WANG

DOI: https://doi.org/10.16628/j.cnki.2095-8188.2017.07.010

2017-01-01

Abstract:It is necessary to carry out study on typical power supply modes of distribution network in transformer area,in order to achieve clear and structured customer management and make an appropriate balance about power supply need and construction investment according to practical conditions.This paper analyzed the power supply modes of middle and low voltage distribution network in advanced region,and made a detailed comparison of each kind of wiring type applied on domestic and foreign areas in technical capability,economical value,applications as well as pros and cons and other aspects.At last,a technology scheme which could be used for reference to guide the construction of domestic transformer region was forecasted based on the analysis about present situation and development trend.
New Method That Improving Temperature Stability of Electronic Voltage Transformer in Middle Voltage

ZHANG Gui-xin,WAN Xiong,WANG Qiang,WANG Peng

DOI: https://doi.org/10.13336/j.1003-6520.hve.2009.10.004

2009-01-01

Abstract:We introduced an electronic voltage transformer which was based on the principle of the voltage divider,and presented the principle and structure of electronic voltage transformer.The impact of the temperature characteristics was also analyzed.Temperature tests of some electronic voltage transformers were carried out at temperatures from-25°C to 40°C.The calculation errors caused by temperature change were analyzed.Results show that selecting the appropriate size of temperature compensation can reduce the errors of electronic voltage transformer caused by the temperature change.
Research on Application of Transformer Vibration Model in Turn-to-turn Short

Jun GUO,Li-min DU,Sheng-chang JI,Qi SHEN,Xiao-bo OU,Liang LU,Ling-yu ZHU

DOI: https://doi.org/10.3969/j.issn.1673-7598.2011.02.002

2011-01-01

Abstract:Diagnose transformer using vibration method is a new trend which can monitor without shut apparatus down.Based on how vibration signal generates,a transformer tank model is presented in this paper.The vibration signal is obtained in different voltage and different current by using a test transformer.And the modulus is acquired by extracting the fundamental frequency signal and taking it to linear extraction.Tank vibration is also measured,showing a good concordance between estimated and measured value.To test the model's ability to detect turn-to-turn short,the model in a transformer is tested with short fault.It indicates that the difference between the estimated and measured value when transformer is unhealthy is much larger than that when it is healthy.All these theories are useful in the transformer fault detection.
Practical Scheme of Optical Voltage Transformer in High Voltage Substations

Yuanyuan Dai,Mengqi Zhang,Feng Zhang,Binshu Chen,Haozong Wang,Wenzhong Li,Xinzhou Dong

DOI: https://doi.org/10.1109/icet55676.2022.9824406

2022-01-01

Abstract:Optical voltage transformer (OVT) is a new voltage transformer emerging with the development of microelectronics technology, optoelectronic technology and digital technology, which is based on linear photoelectric effect and polarization optics. Compared with traditional transformers, OVT has the advantages of optoelectronic isolation, wide frequency band, high accuracy and wide dynamic range, so OVT was highly expected when it appeared. However, at the early stage of OVT’s promotion, OVT was mainly used to measure power frequency voltage. Moreover, although the capacitive voltage transformer had many shortcomings compared with OVT, it could still well meet the needs of voltage measurement of the current operating equipment and CVT productions are more mature, so the further development of OVT was hindered. The development of traveling wave protection which requires the use of wide frequency band voltages that couldn’t be provided by CVT puts forward new application scenarios for OVT. This paper presents a practical scheme of passive optical voltage transformer in high voltage substations, which could contribute to the further popularization of OVT in substations.
Analysis of transformer protection principle based on voltage and current information

Chenguang YAN,Zhiguo HAO,Baohui ZHANG,Bo SHAO,Anbo YU

DOI: https://doi.org/10.3969/j.issn.1006-6047.2010.10.008

2010-01-01

Abstract:Three transformer protection principles synthetically using the information of voltage and current are analyzed and studied. The magnetic flux characteristics principle applies the law of core magnetic flux variation to identify the transformer operating conditions, but it is difficult to directly measure and calculate the magnetic flux. The equivalent equations principle identifies the transformer operating conditions according to the equations built with the winding parameters and the information of voltage and current in normal operating condition, but it is difficult to get the winding parameters and set the threshold. The power differential principle, based on the law of conservation of energy, reflects the energy changes in different operation conditions veritably, but it needs one period to distinguish the excitation inrush from fault current. The feasibility of these principles is verified by dynamic test and their protective performances are compared. The difficulty of threshold setting restricts its application, for which the improvement direction is given.
Study of Comparison of Voltage Distribution in Transformer under Different Lightning Impulse Voltages

Yun Yang,Qi Wang,Chao Gao,Jinyu Pu,Xuanrui Zhang,Junhao Li

DOI: https://doi.org/10.1109/ichve49031.2020.9279635

2020-01-01

Abstract:Voltage surges arising lightning discharges are one of the chief causes of failure in the transformer winding due to the non-linear distribution of the voltage along the transformer winding. This paper extends the former researches in one aspect by including the voltage distribution under the oscillating lightning impulse voltage (OLI) in comparison with that of standard lightning impulse (SLI). A lumped parameter model of a transformer winding is built and the simulations are carried out to study the voltage distribution across a transformer winding when excited with SLI of different front and tail time and its corresponding OLI of same front and tail time. The voltage between each coil and the ground and the voltage between coils is determined. It is discovered that the oscillation frequency of the winding under OLI is consistent with the frequency of the applied voltage at first and then with the natural frequency. The voltage between coils is highest at coils 1-5. The coil to ground voltage under OLI is generally smaller than that under SLI. This research can be used as a cornerstone for the application of OLI voltage for the on-site insulation dielectric strength test.
High Voltage Testing Transformer Computer Control System With Waveform Analysis Function

Sy Cheng,Zy Cai,Sh Ma

2003-01-01

Abstract:In this paper, an industrial computer control system of high voltage testing transformer is presented. By which, a whole testing process can automatically perform according to the testing criterion or the initialization defined by its user. The test accuracy and the efficiency are improved largely. After testing, the measured data are analyzed by means of wavelet analysis in order to research sample's breakdown. The hardware structure is presented and the software is programmed in this paper.
Study on Transformer Tank Vibration Characteristics in the Field and Its Application

Ji Shengchang,Zhu Lingyu,Li Yanming

2011-01-01

Abstract:Vibration signal analysis method is one of effective methods to monitor the condition of transformer windings and core. In this paper, the multi-channels vibration measurement system is set up and the vibration signals on the oil-tank surface of running transformer in the field are measured. The influences of transformer type and sensor positions on the measured vibration signals are analyzed. The results show that, the same type of transformer' oil tank vibration signals have almost same characteristics, and the vibration signals measured on a transformer tank surface have similar characteristics only at the same position of phase "A"(or "a") and "C"(or "c"). Moreover, the attachment position of each sensor should be marked on the tank surface with paint, which is the reference position in the next measurement. It was recommended that the permissible error in the position of the sensor is within 5cm. The vibration characteristics acquired in the field are applied to diagnose a transformer suffered three-phase short circuit, and the results presented show the accuracy and efficiency of the acquired transformer tank vibration characteristics.
Virtual Instrumentation Solution to Integrated Measurement Platform for Power Transformers

侯毅,韩韬,施文康

DOI: https://doi.org/10.3969/j.issn.1001-8425.2001.01.002

2001-01-01

Abstract:The routine, type and special tests for power transformer are thekey factor of its quality and characteristics. For a long period, the devices for transformer measurement are discrete customized instruments and always manipulated and recorded manually. According to the Virtual Instrumentation solution, a novel type of measuring instument—the integrated measurement platform for power transformer based on the ComponentWorksTM software, Visual Basic and some hardware module is developed. It will improve the accuracy and the efficiency of measurement.
Study on Automatic Voltage Regulation Technology of Rural Power Grids

SUN Meng,ZHAO Yulin,FU Yan

DOI: https://doi.org/10.3969/j.issn.1005-9369.2012.05.016

2012-01-01

Abstract:Through technical reconstruction,the rural power grid voltage quality has been improved.But the voltage fluctuation range is still lager than the allowable value of national regulation.This situation seriously restricts the development of rural economy.This paper studied a non-contact on-load voltage regulation tap changer wiring and its control method.Used the way of connecting the regulating windings of distribution transformer positive and negative to achieve the goal of stabilizing the voltage of rural power grids.Theory analysis and simulation experiment manifested that this stabilizing voltage technology had advantages of large voltage regulating range,low actual beard voltage of elements and simple structure.And this technology was suitable for rural power grid.
Study on Return Voltage Measurement of Oil-paper Insulation Testing Technology in Transformers

Shaorui Qin,Daning Zhang,Guocheng Ding,Taiyun Zhu,Yuan Li,Guanjun Zhang,Chenchen Zhang

DOI: https://doi.org/10.1109/icdl.2017.8124630

2017-01-01

Abstract:Transformer is one of the most important equipment in the power system, assuming the voltage conversion, distribution, transmission of electrical energy mandate in power network, which is an important prerequisite for safe and stable operation of power system. Once the transformer fault, it may lead to blackouts, and even the collapse of the power network, causing huge economic losses. From the point of view of economy and safety, it is necessary to carry out insulation diagnosis and life assessment for prolonging the service life of power transformer. Dielectric response measurements are a technology that is used to detect the insulation condition of transforms. In recent years, a series of non-destructive test methods based on the dielectric response theory of transformer have been developed, including frequency domain dielectric spectroscopy (FDS) in the frequency domain and the polarization and depolarization current (PDC), the return voltage method (RVM) in time domain. On the basis of dielectric response technology, this paper discusses the time domain dielectric spectroscopy of PDC and RVM, also including the conversion algorithm between the two methods. The RVM method has the advantage of adjusting the discharge resistance of the external circuit, which can calculate the equivalent parameters of dielectric, and the PDC takes into account the characteristics of the oil, the conductivity of the oil, the insulation structure and material properties and so on. The physical basis of the RVM and PDC methods is similar, but the use of the RVM method for testing is more complex than the PDC method. So it is necessary to study the conversion algorithm from PDC to RVM, which improve the flexibility of time domain dielectric spectrum test. The derivation and experimental verification of the algorithm are presented in this paper.
Research of a transformer fault diagnose method using multi-source recording waves

Haosheng Huang,Yu Liu,Yubo Yuan,Peng Li

DOI: https://doi.org/10.1109/CICED.2014.6991833

2014-01-01

Abstract:Power transformer is one of the most important and expensive devices in power system. Fault in a transformer has a large influence so that the operation statuses of it directly affect the safety of power system. However, it is difficult to diagnose fault location because transformer faults may be caused by many factors and occur in many places for its complex structure. This paper proposed a transformer fault diagnose method by using voltage and current from fault recorder and protection devices of all voltage levels, as well as sequence components of them. Characteristics of current from all voltage levels are recognized by analyzing sequence components of currents derived from special TAs and bushing TAs under several fault situations. Then, a correspondence relationship between the transformer fault location and fault record wave is established to determine fault location quickly. Finally, the paper analyzed a real case of 220kV transformer fault to verify the effectiveness and usefulness of the method. Transformer fault can be quickly and accurately located using the proposed method, which makes the outage time shortened, thus improving the stability and security of power grid.

Voltage Transformer and Study of Its Using

Research on Short-Circuit Vibration of Power Transformer

The Error Analysis on Voltage Transformer and Things to be Noticed

Voltage Transformer Winding Impulse Over-Voltage Study

Analysis and Treatment of Electronic Voltage Transformers Exceeded Tolerance Problem

Analyses on an electronic voltage transformer's failure by its resonance with very fast transient overvoltage and suppression

On-Load Automatic Voltage Regulation System Designed Via Thyristor for Distribution Transformer

Novel Progress in the Research of Piezoelectric Transformer

Research on Medium-voltage Electronic Transformers

Research on Typical Power Supply Modes of Middle and Low Voltage Transformer Areas at Home and Abroad

New Method That Improving Temperature Stability of Electronic Voltage Transformer in Middle Voltage

Research on Application of Transformer Vibration Model in Turn-to-turn Short

Practical Scheme of Optical Voltage Transformer in High Voltage Substations

Analysis of transformer protection principle based on voltage and current information

Study of Comparison of Voltage Distribution in Transformer under Different Lightning Impulse Voltages

High Voltage Testing Transformer Computer Control System With Waveform Analysis Function

Study on Transformer Tank Vibration Characteristics in the Field and Its Application

Virtual Instrumentation Solution to Integrated Measurement Platform for Power Transformers

Study on Automatic Voltage Regulation Technology of Rural Power Grids

Study on Return Voltage Measurement of Oil-paper Insulation Testing Technology in Transformers

Research of a transformer fault diagnose method using multi-source recording waves