Abstract:This paper reports on a novel process for preparing open-cell polymer foams which consists in (1) blending a desired polymer with one which is much more CO2-philic and which is the dispersed phase, (2) tuning the sea-island type of morphology of the polymer blend to a co-continuous type by selectively swelling the CO2-philic polymer with CO2 saturation, and (3) selectively foaming the CO2-philic polymer by CO2 depressurization. More specifically, a blend composed of 70% of isotactic polypropylene (PP) and 30% of a copolymer of ethylene-propylene-diene monomer (EPDM) is chosen to show the working principle and potential of the above process. PP is a desired polymer and EPDM a CO2-philic one. During the CO2 saturation, the initially sea-island type of morphology of the PP/EPDM (70/30) blend evolves into a more or less co-continuous one due to the much more CO2-philic nature of the EPDM. Upon CO2 depressurization, foaming takes place primarily in the EPDM phase, leading to open cells. To achieve open-cells for the PP/EPDM (70/30) blend, it is necessary to search for an optimum CO2 saturation pressure and temperature window. Within this window, the cell size and the expansion ratio are in the range of 1.5-17.5 mu m and 1.5-6.6, respectively. Tensile results show that the elongation at break of the CO2 saturated and foamed PP/EPDM blends is higher than that of the un-treated one, indicating that the co-continuous morphology of the PP/EPDM blend improves its toughness. Moreover, compression results indicate that the open-cell foams exhibit good flexibility and elasticity. (C) 2016 Elsevier Ltd. All rights reserved.

Preparation and Mechanical Properties of Polyphenylene Sulfone Foams

Study on the Foaming Behaviors of PBS and its Modification with PA6IcoT Assisted by scCO2

Static and Dynamic Behavior of PU Foams with Multilayer Coatings

Microstructure and Properties of Microcellular Poly (phenylene Sulfide) Foams by Mucell Injection Molding

Mechanical Properties of Polyurethane Foams Prepared from Liquefied Corn Stover with PAPI.

Preparation of Polypropylene Foams with Bimodal Cell Structure Using a Microporous Molecular Sieve As a Nucleating Agent

Preparation and properties of PP/SEBS foam materials

Foaming Window for Preparation of Microcellular Rigid Polyurethanes Using Supercritical Carbon Dioxide As Blowing Agent

Preparation and characterization of microcellular injection molded foams from high-performance blends based on PPS-modified PPBESK

Preparation of Open-Cell Polymer Foams by CO2 Assisted Foaming of Polymer Blends

Study on Extrusion Foaming of Polypropylene/Polydimethylsiloxane Blends

Microcellular Foaming of Polysulfones in Supercritical CO2 and the Effect of Co-Blowing Agent

Batch Foam Processing of Polypropylene/Polydimethylsiloxane Blends

Strategy for Preparation of Microcellular Rigid Polyurethane Foams with Uniform Fine Cells and High Expansion Ratio Using Supercritical CO2 As Blowing Agent

Experimental and Numerical Study of the Polyurethane Foaming Process Using High-Pressure CO2

Synergistic effects of in situ fibrillated polytetrafluoroethylene and polystyrene–butadiene block on the microcellular foaming behaviors of polyphenylene oxide modified by high‐impact polystyrene

Application of a CO2 Pressure Swing Saturation Strategy in PP Semi-Solid-State Batch Foaming: Evaluation of Foamability by Experiments and Numerical Simulations

Biodegradable and Ultra-High Expansion Ratio PPC-P Foams Achieved by Microcellular Foaming Using CO2 as Blowing Agent

Preparation of high-expanded PP foams with chemical blowing process

Preparation, Characterization, and Mechanical Properties of Microcellular Poly(Aryl Ether Ketone) Foams

Mechanical and Flame‐resistance Properties of Polyurethane‐imide Foams with Different‐sized Expandable Graphite