Abstract:In this study, polyurethane (PU) foams were manufactured using kraft lignin and castor oil as bio-based polyols by replacing 5–20 wt% and 10–100 wt% of conventional polyol, respectively. To investigate the effects of unmodified bio-based polyols on PU foam production, reactivity and morphology within PU composites was analyzed as well as mechanical and thermal properties of the resulting foams. Bio-based PU foam production was carried out after characterizing the reagents used in the foaming process (including hydroxyl group content, molecular weight distribution, and viscosity). To compare the resulting bio-based PU foams, control foam were produced without any bio-based polyol under the same experimental conditions. For lignin-incorporated PU foams, two types, LPU and lpu, were manufactured with index ratio of 1.01 and 1.3, respectively. The compressive strength of LPU foams increased with lignin content from 5 wt% (LPU5: 147 kPa) to 20 wt% (LPU20: 207 kPa), although it remained lower than that of the control foam (PU0: 326 kPa). Similarly, the compressive strength of lpu foams was lower than that of the control foam (pu0: 441 kPa), with values of 164 kPa (lpu5), 163 kPa (lpu10), 167 kPa (lpu15), and 147 kPa (lpu20). At 10 wt% lignin content, both foams (LPU10 and lpu10) exhibited the smallest and most homogenous pore sizes and structures. For castor oil-incorporated PU foams with an index of 1.01, denoted as CPU, increasing castor oil content resulted in larger cell sizes and void fractions, transitioning to an open-cell structure and decreasing the compressive strength of the foams from 284 kPa (CPU10) to 23 kPa (CPU100). Fourier transform infrared (FT-IR) results indicated the formation of characteristic urethane linkages in PU foams and confirmed that bio-based polyols were less reactive with isocyanate compared to traditional polyol. Thermogravimetric analysis (TGA) showed that incorporating lignin and castor oil affected the thermal decomposition behavior. The thermal stability of lignin-incorporated PU foams improved as the lignin content increased with char yields increasing from 11.5 wt% (LPU5) to 15.8 wt% (LPU20) and from 12.4 wt% (lpu5) to 17.5 wt% (lpu20). Conversely, the addition of castor oil resulted in decreased thermal stability, with char yields decreasing from 10.6 wt% (CPU10) to 4.2 wt% (CPU100). This research provides a comprehensive understanding of PU foams incorporating unmodified biomass-derived polyols (lignin and castor oil), suggesting their potential for value-added utilization as bio-based products.

Mechanical Properties of Polyurethane Foams Prepared from Liquefied Corn Stover with PAPI.

Optimization of Reaction Conditions for Polyurethane Foam Synthesis with Liquefied Corn Stalk by Response Surface Methodology

Processing and properties of rigid polyurethane foams based on bio-oils from microwave-assisted pyrolysis of corn stover

Simultaneous Interpenetrating Polymer Networks of Polyurethane from Pentaerythritol–Modified Castor Oil and Polystyrene: Structure–Property Relationships

Study on the Foaming Behaviors of PBS and its Modification with PA6IcoT Assisted by scCO2

Effect of Surface Modification of Montmorillonite on the Properties of Rigid Polyurethane Foam Composites

Optimizing the preparation parameters of eco‐friendly flexible polyurethane foams derived from a corn‐based bio‐polyol

Preparation and properties of novel poly(propylene oxide)-block- polylactide-based polyurethane foams

Comprehensive Investigation of Stoichiometry–Structure–Performance Relationships in Flexible Polyurethane Foams

Preparation of Mechanically Robust Bio-Based Polyurethane Foams Using Depolymerized Native Lignin

Pulverized Polyurethane Foam Particles Reinforced Rigid Polyurethane Foam And Phenolic Foam

Preparation and characterization of polyurethane foam using a PLA/PEG polyol mixture

Successive organic solvent fractionation and homogenization of technical lignin for polyurethane foam with high mechanical performance

Study on preparation and performance of PEG-based polyurethane foams modified by the chitosan with different molecular weight

Preparation of rigid polyurethane foam from lignopolyol obtained through mild oxypropylation

Effects of polyvinyl alcohol content and hydrolysis degree on the structure and properties of extruded starch-based foams

Fractionated lignin as a polyol in polyurethane fabrication

Synthesis and characteristics of nonisocyanate polyurethane composed of bio‐based dimer diamine for supercritical CO2 foaming applications

Investigation of bio-based rigid polyurethane foams synthesized with lignin and castor oil

Effect of Liquefied Lignin Content on Synthesis of Bio-based Polyurethane Foam for Oil Adsorption Application

Study on the Mechanical Properties of Hybrid Reinforced Rigid Polyurethane Composite Foam