Abstract:The mechanical interaction between welded panel and fixture has a remarkable influence on the distribution of weld induced residual stress and distortion.Unfortunately,the influence of fixture is not generally included in conventional numerical simulations of welding process.In the present study,it is proposed that the numerical models in which the mechanical interaction between welded panel and fixture is considered as contact pair in the finite element analysis(FEA) of welding process.This could make the FEA of welding process more scientific and accurate.The fixture constraint plays an important role in accurate modeling of welding process.In the simulations,various mechanical constraint boundary conditions in welding process were thought about to establish the relationships of the normal and tangential mechanical interactions between welded panel and fixture. In Free model,the fixture restraint was not considered.In Mech model,the displacements of nodes where welded panel contacted with fixture were restricted in x,y,z directions.Hard model and Tabular model were contact models which included the fixture.In the normal direction,once welded panel and fixture were in contact,the transmitted contact pressure could be infinite in Hard model.While data pairs of contact pressure vs over-closure or clearance were specified to define a piecewise-linear relationship in the normal direction in Tabular model.A penalty friction coefficient of 0.3 was applied in tangential direction in both Hard and Tabular models.Fixture and welded panel were separated and the contact relationships were removed after the welding process in both Hard and Tabular models. The simulation results of contact models including fixture were more accurate,compared to models containing only welded panel with rigid restrictions.The distortion mode of welded panels under different fixture constraint conditions corresponded well with experimental results.The differences between the distributions of transverse stresses on top and bottom surfaces of welded panel at the beginning of welding process had a crucial influence on the distortion mode of welded panel.

On Welding Constraint Forces of a Ship Bottom Grillage

A Study on the Spring-Back Deflections and Constraint Forces of a Bottom Grillage Cling Welding

Study of vertical mechanical constraint on welding deformation and residual stress of a deck grillage

Experimental and Numerical Studies on the Ultimate Bending Strength of Welded Plated Grillage with Combined Openings

Numerical Prediction and Control of Deformation and Residual Stress in Double-Sided Arc Welding of Large Pressure Hull

ESTABLISHMENT AND APPLICATION OF FIXTURE CONSTRAINT MODELS IN FINITE ELEMENT ANALYSIS OF WELDING PROCESS

Numerical Analysis on Optimizing Welding Sequence of Large-Sized Bottom Structure for Controlling Welding Distortion

Numerical Prediction of Welding Distortion Considering Gravity Force on General Ship Grillage Structure by Elastic Finite Element Method Using Inherent Strain

Researches on mechanical properties of welding reinforcement of end plate connection nodes in steel-structure under loadsby finite element analysis

Analysis of the Stress around the Shell-to-bottom Fillet Welds of Large Oil Tanks

Research of Complicated Ship Structure Welding Distortion Based on ANSYS

Experiments and Numerical Simulations on Laser Welding Deformation of Thin Plate Considering Constraint Clamp

The Influence of Welding-Induced 3D Residual Stress and Distortion on the Ultimate Strength of Multi-Stiffened Thin Plate Structures under Cyclic Load

Investigating Welding Distortion of Thin-Plate Stiffened Panel Steel Structures by Means of Thermal Elastic Plastic Finite Element Method

Numerical Simulation and Measurement of Welding Residual Stresses in Orthotropic Steel Decks Stiffened with U-Shaped Ribs

Thermal elastic-plastic FEM analysis of welding deformation and residual stress of a stiffened plate structure in hull

Thermal-Elastic-Plastic Finite Element Analysis for Laser Welding Deformation of Thin Plate

Effects of External Restraining Forces oH Bead-on-plate Welding Residual Stress

Research on welding deformation for box girder of bridge crane based on thermal elasto-plastic theory

Comparative Study of Welding Deformation of a Stiffened Panel under Various Welding Procedures

Prediction of Welding Deformation and Residual Stress in A Multiply-Stiffened Plate