Abstract:In order to study the effect of stitching density, tow size of the suture and diameter of the stitching hole on the shear property of the stitched three-dimensional woven composite/titanium hybrid board stitching connection structure, seven groups of samples with different stitching densities, tow size of the suture and diameter of the stitching hole were tested. A reference group whose samples were unstitched was also tested to show the effect of stitching on the joint. Different failure modes of the lap zone with different stitching parameters were observed in in-situ mesoexperiment, and the damage morphologies of the characteristic points on the load-displacement curve were given. The result shows that increasing tow size of the suture and increasing stitching density can both increase the failure load of the hybrid joint. Increasing the stitching density is proved more effective in improving the failure load. Doubling the stitching density can increase the failure load of the stitched joint about 82. 0%. Doubling the tow size of the suture can only increase the failure load of the joint about 24. 3%; Whether the diameter of the stitching hole is 2 mm or 4 mm do not influence the bearing capacity of the structure obviously, and when the stitching hole diameter reaches 6 mm, the bearing capacity is reduced due to the low strength of the epoxy resin in the gap between stitching hole and suture. It is dangerous to increase diameter of stitching hole above 4 mm; the shear failure of the stitched three-dimension woven composite/titanium alloy hybrid structure is observed by mesoscopic mechanical test. Composite/titanium alloy interface failure, crack initiation and extension in composite or in lap zone and failure of the lap zone are the three main stages of the structure failure observed in the test; The suture failure in the connect zone includes suture pull out and suture cut off. There are three failure modes of the lap zone observed in test. In suture cut off mode, all sutures in lap zone are cut off. The position at which the suture is cut is related to the diameter of the stitching hole. In suture cut off/pull out mixed mode, some of the interface between suture and threedimension woven composites fail and the suture is partly or completely pull out. In the group with high stitching density, sutures near the end of the three-dimension woven composite crush the composite and extrude out of the composite. Stitching density is the major factor in the failure mode of the joint.

Experiment and Analysis on Mechanical Properties of Stitched Laminates

EFFECTS OF STITCHING PARAMETERS ON IN-PLANE STIFFNESS AND STRENGTH OF COMPOSITE LAMINATES

EFFECT OF MESO-STRUCTURE CHARACTERISTICS ON MECHANICAL PROPERTY OF STITCHED COMPOSITES

Study on Stiffness of Stitched Laminates

Experimental study on the stitching reinforcement of composite laminates with a circular hole

STUDY ON CONSTITUTIVE RELATIONSHIP OF STITCHED LAMINATES(II) --Analytical and Experimental Study on Stiffness of Stitched Laminates

Experimental and Numerical Analysis of Stitched Composite Laminates Subjected to Low-Velocity Edge-on Impact and Compression after Edge-on Impact

Experimental Investigation of Interlaminar Fracture Toughness of CFRP Composites with Different Stitching Patterns

Effect of Stitches on the Permeability of Interbundle Channels in Stitched Fabrics

Shear Stiffness Prediction of Stitched Composite Sandwich Structure with Foam Core

Finite Element Analysis of Low-Velocity Impact Damage of Stitched Laminates

Flexural Fatigue Properties and Failure Propagation of 3D Stitched Composites under 3-Point Bending Loading

Failure mechanism of stitched three dimension woven composite/Ti alloy hybrid board joint under shear load

Multi-scale numerical analysis of damage modes in 3D stitched composites

Fracture Phase Field Modeling of 3D Stitched Composite with Optimized Suture Design

Mechanical Responses and Damage Morphology of Laminated Fabrics with a Central Slit under Uniaxial Tension: A Comparison Between Analytical and Experimental Results

Influence of Stitch Angle on the Flexural Response of Composite Structures

Deformation and Fracture Mechanisms of Automated Fiber Placement Pre-Preg Laminates under Out-of-plane Tensile Loading

Investigation and prediction of laminate quality and interlaminar mechanical performance of the tufted sandwich composites with different core structures

Investigation of the translaminar fracture behavior of the fiber-reinforced composites stitched perpendicular to their plane

Effect of stitching angle on mechanical properties of stitched sandwich panels