Abstract:In order to study the effect of stitching density, tow size of the suture and diameter of the stitching hole on the shear property of the stitched three-dimensional woven composite/titanium hybrid board stitching connection structure, seven groups of samples with different stitching densities, tow size of the suture and diameter of the stitching hole were tested. A reference group whose samples were unstitched was also tested to show the effect of stitching on the joint. Different failure modes of the lap zone with different stitching parameters were observed in in-situ mesoexperiment, and the damage morphologies of the characteristic points on the load-displacement curve were given. The result shows that increasing tow size of the suture and increasing stitching density can both increase the failure load of the hybrid joint. Increasing the stitching density is proved more effective in improving the failure load. Doubling the stitching density can increase the failure load of the stitched joint about 82. 0%. Doubling the tow size of the suture can only increase the failure load of the joint about 24. 3%; Whether the diameter of the stitching hole is 2 mm or 4 mm do not influence the bearing capacity of the structure obviously, and when the stitching hole diameter reaches 6 mm, the bearing capacity is reduced due to the low strength of the epoxy resin in the gap between stitching hole and suture. It is dangerous to increase diameter of stitching hole above 4 mm; the shear failure of the stitched three-dimension woven composite/titanium alloy hybrid structure is observed by mesoscopic mechanical test. Composite/titanium alloy interface failure, crack initiation and extension in composite or in lap zone and failure of the lap zone are the three main stages of the structure failure observed in the test; The suture failure in the connect zone includes suture pull out and suture cut off. There are three failure modes of the lap zone observed in test. In suture cut off mode, all sutures in lap zone are cut off. The position at which the suture is cut is related to the diameter of the stitching hole. In suture cut off/pull out mixed mode, some of the interface between suture and threedimension woven composites fail and the suture is partly or completely pull out. In the group with high stitching density, sutures near the end of the three-dimension woven composite crush the composite and extrude out of the composite. Stitching density is the major factor in the failure mode of the joint.

Failure mechanism of stitched three dimension woven composite/Ti alloy hybrid board joint under shear load

Strengthening of Composite T-joints Using Ø 0.11 Mm Z-pins Via an Ultrasound-Guided Insertion Process

Experiment and Analysis on Mechanical Properties of Stitched Laminates

Fracture Phase Field Modeling of 3D Stitched Composite with Optimized Suture Design

Flexural Fatigue Properties and Failure Propagation of 3D Stitched Composites under 3-Point Bending Loading

Effects of Stitch Yarns on Interlaminar Shear Behavior of Three-Dimensional Stitched Carbon Fiber Epoxy Composites at Room Temperature and High Temperature

Investigating the Effects of Contact Area and Chamfering on the Failure Behavior of Plain Woven Composite-Metal T-joints

Experimental characterization of failure behaviour for three-dimensional woven carbon/carbon composites under pin-loading

EFFECTS OF STITCHING PARAMETERS ON IN-PLANE STIFFNESS AND STRENGTH OF COMPOSITE LAMINATES

Out-of-plane Properties and Failure Mechanism of Composite Laminates Reinforced with Carbon Z-pins

Experimental and Numerical Study on Failure Behaviors of Composite Grid Stiffeners under Tensile and Flexural Loading

Multiaxial failure mechanism of 3D triple-twill warp-lining woven composites

Multi-scale numerical analysis of damage modes in 3D stitched composites

Experimental and Multiscale Numerical Investigation on Failure Behavior of Satin Woven Carbon/carbon Composites Subjected to Pin-Loading

Study on Tensile and Compressive Properties and Size Effect of 3D Fine Woven Punctured C/C Composites

Tensile Failure Analysis of Carbon Fiber Composite Material L-shaped Joint

Experimental study on the stitching reinforcement of composite laminates with a circular hole

Experimental Characterization for Failure Behavior of Woven Modified Carbon/Carbon Composites Under Pin-Loading

Parametric study on the load-carrying capacity of plain-woven composites hybrid bonded-bolted joints

Experimental investigation on shear damage evolution of 3D woven composites using in situ computed tomography and multi-scale digital image correlation

Effect of stitch density on the damage inhibition and compression strength after high-velocity impact of UHMWPE fiber composites