Abstract:Temperature has a great influence on the mechanical properties of ductile cast iron or nodular cast iron. A thermomechanical treatment was carried out at various elevated temperatures of 450 °C, 750 °C and 850 °C using a universal testing machine with a tub furnace. Specimens were held at these temperatures for 20 min to ensure a homogeneous temperature distribution along the entire length of the specimen, before a tensile load was applied. Specimens were deformed to various levels of uniform strain (0%, 25%, 50%, 75%, and 100%). These degrees of deformation were measured with a dial gauge attached to a movable cross plate. Three strain rates were used for each specimen and temperature: 1.8×10−4 s−1, 9×10−4 s−1 and 4.5×10−3 s−1. A simple analytical model was extracted based on the CT tensile test geometry and yield stress and a 0.2% offset strain to measure the fracture toughness (JIC). To validate the analytical model, an extended finite element method (XFEM) was implemented for specimens tested at different temperatures, with a strain rate of 1.8×10−4 s−1. The model was then extended to include the tested specimens at other strain rates. The results show that increasing strain rates and temperature, especially at 850 °C, increased the ductility of the cast iron and thus its formability. The largest percentage strains were 1 and 1.5 at a temperature of 750 °C and a strain rate of 1.8×10−4 s−1 and 9×10−4 s−1, respectively, and reached their maximum value of 1.7 and 2.2% at 850 °C and a strain rate of 9×10−4 s−1 and 4.5×10−3 s−1, respectively. In addition, the simple and fast analytical model is useful in selecting materials for determining the fracture toughness (JIC) at various elevated temperatures and different strain rates.

Influence of Maximum Temperature on Thermal Fatigue Resistance of Ductile Iron

Influence of Thermal Cycle Maximum Temperature on Thermal Fatigue Resistance of Vermicular Graphite Cast Iron

Influence of Maximum Temperature on Thermal Fatigue Resistance of High Silicon-Molybdenum Vermicular Graphite Cast Iron

Effect of cyclic straining at elevated-temperature on static mechanical properties, microstructures and fracture behavior of nickel-based superalloy GH4145/SQ

Effect of Fatigue Load on High-Temperature Tensile Properties of P92 Steel

Low-Cycle Fatigue Damage Mechanism and Life Prediction of High-Strength Compacted Graphite Cast Iron at Different Temperatures

A comparative study of low cycle fatigue behavior and microstructure of Cr-based steel at room and high temperatures

Influence of temperature on tensile properties of T91 ferritic/martensitic steel

Effect of thermal exposure on the microstructure and mechanical properties of Ti60 alloy

High fatigue performance and microscopic mechanisms of in-situ TiB 2 /7050Al composite at different temperatures

Study on thermal fatigue stability in microstructure and mechanical property of Fe35Ni35Cr20Mn10 high-entropy alloy wire and pearlite wire at high/medium temperature environment

Mechanical Properties and Fracture Toughness Prediction of Ductile Cast Iron under Thermomechanical Treatment

Effect of the Austenitizing Temperature on Microstructure Evolution and Impact Toughness of a Novel Bainite Ductile Iron

Influence of Welding Technique and Temperature on Fatigue Properties of Steel Deposited with Co-Based Alloy Hardfacing Coating

Temperature effect on the low cycle fatigue behavior of a directionally solidified nickel-base superalloy

Study on fatigue temperature evolution and failure behavior of Q460 steel

Mechanism of Fatigue-Life Extension Due to Dynamic Strain Aging in Low-Carbon Steel at High Temperature

The fatigue properties, microstructural evolution and crack behaviors of low-carbon carbide-free bainitic steel during low-cycle fatigue

The low cycle fatigue property, damage mechanism, and life prediction of additively manufactured Inconel 625: Influence of temperature

The Low-Cycle Fatigue Behavior, Microstructure Evolution, and Life Prediction of SS304: Influence of Temperature

Failure mode and hot ductility of Ti-bearing steel in the brittle zone